6.8 Calculate the hydraulic detention time (0) of a CSTR with settled-solids recycle if Y = 0.6 g VSS,/g BOD ĝ = 20 g BOD,/g VSS,-d K = 20 mg BOD,/1 b = 0.25/d f = 0.8 S° = 10,000 mg BOD,/1 X = 4000 mg/1 X = 0 0. = 6 d Q = 1000 m³/d %3D Discuss the practicality of treating this rather high-strength soluble wastewater by this method.

6.8 Calculate the hydraulic detention time (0) of a CSTR with settled-solids recycle if Y = 0.6 g VSS,/g BOD ĝ = 20 g BOD,/g VSS,-d K = 20 mg BOD,/1 b = 0.25/d f = 0.8 S° = 10,000 mg BOD,/1 X = 4000 mg/1 X = 0 0. = 6 d Q = 1000 m³/d %3D Discuss the practicality of treating this rather high-strength soluble wastewater by this method.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: : For the concrete Dam shown in figure, determine the total average seepage for the given permeable…

A: To find total seepage

Q: 4- Refer to Figure below. If H1=3 ft, H2=4.5 ft, h=1.5 ft, ysa=118.9 lb/ft³, area of the tank=6.25…

Q: For the branching pipe system in the figure below, if the discharge through pipe A is given, which…

A: The branching pipe system is given in the above figure. Discharge through pipe A is given. We have…

Q: For the hydraulic system shown below, calculate the total head, elevation head, pressure head, and…

A: Coefficient of permeability of soil 1, Coefficient of permeability of soil 2, To find: The total…

Q: A sand sample of 40cm^2 cross-sectional area and 25cm long was tested in a constant head…

A: From the question, we can identify the following values:Cross-sectional area (A) = 40 cm^2Length of…

Q: A 25 cm diameter pipe carries air (p=1.22kg/m³) (v = 1.5x10-5m²/sec) at an average velocity of 8.0…

Q: The diameter of a pipe gradually reduces from 1m to 0.7 m. the pressure intensity at the centre line…

Q: You are designing a storm drain for a new parking lot. The topographic conditions at the site…

A: Pipe slope = 0.013Flowrate = 17 cfsConsider, the use of concrete pipe (n= 0.013)use of corrugated…

Q: H k, H, k, Н. H. k, Referring to the figure above, estimate the equivalent hydraulic conductivity…

Q: A 25 cm diameter pipe carries a (p=1.22kg/m³) (v=1.5x10-5m²/sec) at a average velocity of 8.0 m/sec.…

Q: Estimate the hydraulic gradient in a 2.2 m diameter smooth concrete pipe carrying a discharge of 3.4…

Q: Review the three cases of flow through porous media shown below. For each case, consider and…

A: This is a question about Darcy’s law, which describes the flow of a fluid through a porous medium.…

Q: Determine the elevation, pressure, and total hydraulic heads at all points, a through g using Datum…

A: step 1-

Q: A 20 cm diameter pipe cc flow regime. The fri estimated as 0.02 for velocity of flow is 4 m stress.…

Q: 1. For the flow net shown in the figure below, if the datum is selected at the downstream water…

Q: Sand IDft 810 pef 菁 Sand 8sat= 120 pcf f= 35°

Concept explainers

Unit Conversion

Standard units are also called SI units. SI units are used for measuring a physical quantity satisfying certain conditions. There are two types of units: fundamental units and derived units. Fundamental units are physical quantities that are independent, that is, they do not depend on other quantities like mass, length, or time. There are plenty of quantities in our lives which need to be measured and compared. Measuring is the comparison of a particular physical quantity with its reference value. A unit is a measure of a fixed physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.

Question

6.8 Calculate the hydraulic detention time (0) of a CSTR with settled-solids recycle if
Y = 0.6 g VSS,/g BOD,|
ĝ = 20 g BOD,/g VSS,-d
K = 20 mg BOD¸/1
b = 0.25/d
f, = 0.8
S° = 10,000 mg BOD,/1
X_
= 4000 mg/1
X = 0
0. = 6 d
Q = 1000 m³/d
%3D
Discuss the practicality of treating this rather high-strength soluble wastewater by
this method.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A decision has to be made on wether touse 3 in or 4 in ID tubing for a well with the flowing conditions: steady state flow Initial =2500 psi Pressure PI=2.0STB/psi Bubble point pressure =1200 psi Depth(TVD)=5000ft Required THP=300psi GOR=200 SCF/bbI
Horizontal commercial steel (new) pipe, 150m in diameter, carries 3.5 m^2/sec of water at 20°C. Calculate the pressure change in the pipe per km length = 1.300 x 10^4 m^2/sec and roughness = 0.045 mm for the pipe.
Note:hand written solution not allowed.
Help pls, Thankyou
A long, straight, horizontal 1000 ft length of 2 ft diameter pipe carries a 60°F water flow of 30 cfs. At this temperature, the water density is 1.94 slug/ft³, and the viscosity is 2.35x105 slug/ft-s. The equivalent sand grain roughness of the pipe is 0.0033 ft. What is the pressure drop over this length of pipe?
A cast-iron pipe was installed 50 years ago with a measured friction factor, f, of 0.02and surface roughness height, e, of 0.2mm. The horizontal pipe is 1500m long and has a diameter of35cm. Since installation, significant tuberculation has developed on the inside walls of the pipe. A recentpipe test was conducted. The pressure drop across the entire length of pipe was measured to be 200kPa.The design discharge through the pipe has not changed over the years (Q=0.1m 3 /s, T=20°C). Determinethe current effective friction factor, f, and surface roughness, e, after years of tuberculation buildup.
Two Water flows from reservoir A to reservoir B through two pipes as shown below. Determine 1) thedischarge in the pipe, 2) the pressure at point P. Assume α = 1.0 at all locations and neglect any minor headloss
6) Water in a hydraulic press initially at 137KPA absolute is subjected to pressure of 116,280KPA absolute. using Eb=2.5 GPa, determine the percentage decrease in the volume of water.
- Once answered correctly will UPVOTE!!
Handwritten pls.
) Determine the elevation, pressure, and total hydraulic heads at all points, a through g using h = 0.1 m Datum 2 h = 0.3 m h2 = 0.2 m %3D L=0.6 m Datum 1 A = 0.15 m2. Datum 2.
ing Example: Pressure gage B is to measure the pressure at point A in a water flow. If the pressure at B is 9 t'm2 , estimate the pressure at A. ywater - 10 KN/m', yHg = 133.7 KN/m, yoil- 9 KN/m³ plution oil Scm It cm