Each of the four vertical links has an 8*36-mm uniform rectangular cross section and each of the four pins has a 16-mm diameter. Determine the maximum value of the average normal stress and the bearing stress in all links and determine the shearing stress in pins. 0.4 m 0.25 m 0.2 m B 20 kN

Q: The joint is subjected to a force of P = 2-- lb and F = 150 lb. Determine the state of stress at…

A:

Q: The piece of wood shown below was used in an experiment. During the test it sheared parallel to the…

A: Given:P=1750 lbt=2.5 inL=5 in

Q: The small steel plate is connected to the right angle bracket by a 6 mm diameter bolt and the…

A:

Q: The pin-connected frame supports the loads P1 = 5 kN and P2 = 10 kN. Determine for an angle of α =…

A:

Q: The steel shafts is made from two segments AB and BC, which are connected together using a fillet…

A:

Q: The five-bolt connection shown must support an applied load of P = 370 kN. If the average shear…

A: Given data as per the question Applied load =370 KN Average shear stress =200Mpa

Q: d2 mm 60 mm FAN dlmm 10 mm 40 mm The shaft shown is subjected to the axial force(F) of 30 kN. If the…

A:

Q: 1. The cylindrical pressure vessel has an inner radius of 1.25 m and a wall thickness of 15 mm. It…

A: Given data :- The inner radius = 1.25 m                         The thickness of wall = 15 mm…

Q: Determine the shear stress at point B on the web of the cantilevered strut at section a–a.

A: Given Applied loads 2 kN and 4 kN To find Shear stress at point B

Q: Determine the principal stress and absolute maximum shear stress developed at point B on the cross…

A:

Q: Determine the maximum w that can be applied if the shear stress limit is 100 MPa. Then determine the…

A:

Q: The lap joint is fastened by 5 one-inch diameter rivets. For P = 10 kips, determine (1.) the maximum…

A: Givenn=5d=1inP=10kipst1=34int2=58inw=4in

Q: An assembly is subjected to a torque (710 lb-in). If the allowable shear stress for the material is…

A: Given:Diameter of smaller section = d = 0.75 inDiameter of bigger section = D = 1.5 inTo find:The…

Q: b. Determine the maximum value of the average normal stress points C and E. 0.4 m c. Determine the…

A: Here we have given P=20 kNdiameter d= 16mm∑mB=020(0.25)=-FCE(0.4)FCE=-12.5 kN (compr)

Q: The following shaft consists of a tube AB and a solid rod BC. The tube has an inner diameter of 25…

A: Please check sign convention I took compressive as negative.If you have any doubts please comment

Q: 1. The link acts as part of the elevator control for a small airplane. If the attached aluminum tube…

A:

Q: The yoke-and-rod connection is subjected to a 15 tensile force of 5 kN. Determine the average normal…

A:

Q: The five-bolt connection must support an applied load of P = 1800 lb. If the average shear stress in…

A: Solution:     dmin = 0.0987 in

Q: The bell-crank mechanism is in equilibrium for an applied load of F1 = 11 kN applied at A. Assume a…

A: F1= 11 kN= 11000 N a= 250 mm b= 100 mm c= 90 mm θ= 40∘ Diameter, d= 29 mm Thickness, t= 31 mm   To…

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.