Problem 3Solve Problem 1.27, you will need the info in 1.7 to do so.PROBLEM 1.704 mEach of the four vertical links has an 8 x 36-mm uniform rectangularcross section and each of the four pins has a 16-mm diameter.Determine the maximum value of the average normal stress in thelinks connecting (a) points B and D, (b) points C and E.0.2502 m20 kNPROBLEM 1.27For the assembly and loading of Prob. 1.7, determine (a) the averageshearing stress in the pin at B, (b) the average bearing stress at B inmember BD, (c) the average bearing stress at B in member ABC, knowingthat this member has a 10 x 50-mm uniform rectangular cross section.

Answered: Image /qna-images/answer/d63f165e-3a0f-4347-ba20-72f3afac65d1.jpg

Each of the four vertical links has an 8 x 36-mm uniform rectangular cross section and cach of the four pins has a 16-mm diameter. Determine the maximum value of the average normal stress in the links connecting (a) points B and D, (b) points C and E. PROBLEM 1.27 For the assembly and loading of Prob. 1.7, determine (a) the average shearing stress in the pin at B, (b) the average bearing stress at B in member BD, (c) the average bearing stress at B in member ABC, knowing that this member has a 10 x 50-mm uniform rectangular cross section.

Each of the four vertical links has an 8 x 36-mm uniform rectangular cross section and cach of the four pins has a 16-mm diameter. Determine the maximum value of the average normal stress in the links connecting (a) points B and D, (b) points C and E. PROBLEM 1.27 For the assembly and loading of Prob. 1.7, determine (a) the average shearing stress in the pin at B, (b) the average bearing stress at B in member BD, (c) the average bearing stress at B in member ABC, knowing that this member has a 10 x 50-mm uniform rectangular cross section.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

! 4 Required information Two horizontal 5.5-kip forces (P) are applied to pin B of the assembly shown. A 0.8-in. diameter pin is used at each connection. Part 2 of 2 0.5 in. 1.8 in. P 0.5 in. 60° 1.8 in. Determine the maximum value of the normal average stress at the midpoint of link BC. The maximum value of the normal average stress at the midpoint of link BC is ksi.
4) An axial load P of magnitude 75 kN is applied as shown to a short section of a W200x59 rolled-steel member. Determine the largest distance a for which the maximum compressive stress does not exceed 100 MPa. 95 mm
The body of a DaVinci hospital robot made of steel materialThe material was statically loaded. Yield strength of the material 450MPa and the stress values given below occurred. Von Mises andCalculate the safety coefficients for both theories using the Tresca criteria.calculate σx= 80 MPa, σy= -40 MPa, τxy= 50 Mpa Note: Show the calculations in detail
In the hanger shown the upper portion of link ABC is 9-mm thick and the lower portions are each 6-mm thick. Epoxy resin is used to bond the upper and lower portions together at B. The pin at A is of 9-mm diameter while a 6-mm-diameter pin is used at C. Determine (a) the shearing stress in pin A. (b) the shearing stress in pin C, (c) the largest normal stress in link ABC, (d) the average shearing stress on the bonded surfaces at B, (e) the bearing stress in the link at C. 30 mm 150 mm 40 mm 170 mm 240 mm 2400 N 120 m
A pressure vessel of 225-mm inner diameter and 6-mm wall thickness is fabricated from a 1.2 m section of spirally welded pipe AB and is equipped with two rigid end plates. The gage pressure inside the vessel is 2 MPa, and 45-kN centric axial forces P and P' are applied to the end plates. P' A 1.2 m 35⁰ B Determine the shearing stress parallel to the weld. The shearing stress parallel to the weld is P MPa.
The frame shown consists of four wooden members, ABC, DEF, BE,and CF. Knowing that each member has a 2x 4-in. rectangular cross section and that each pin has a 1/2-in. diameter, determine the maximum value of the average normal stress (a) in member BE, (b) in member CF.
PROBLEM 1 Two forces , each of magnitude P, are applied to the wrench. The diameter of the steel shaft AB is 20 mm. Determine the largest allowable value of P if the shear stress in the shaft is not to exceed 120 MPa and its angle of twist is limited to 7 deg. Use G=80 GPa for steel 300 mm s00 mm
solve leteer e
+3 in- B in. A vertical force P of magnitude 20 kips is applied at point C located on the axis of symmetry of the cross section of a short column. Knowing that y = 5 in., determine (a) the stress at point A, (b) the stress at point B, (c) the location of the neutral axis. 2 in. 4 in. A 2 in. 2 in. 1 in. (a) (b)
The ABD rigid bar is connected to the BD rush which consists of a single bar with a width of 25.0 mm and a thickness of 13 mm. Knowing that each pin has a diameter of 10 mm determine the value of the maximum average normal stress on rod BD considering the angle θ= 90°. Calculate the deformation in the BD rod knowing that it is made of steel with an elastic modulus equal to 210 GPa. Knowing that pins A, B and D are made of steel with a limit stress of 180 Mpa, calculate the smallest allowable diameter so that they support the load applied to them considering an overall safety factor of 2.8.
Example An axial centric force of magnitude P= 450 kN is applied to the composite block shown by means of a rigid end plate. Knowing that b-10 mm, determine the normal stress in (a) the brass core, (b) the aluminum plates. Brass core Rigid end plate (E = 105 GPa) Aluminum plates (E = 70 GPa) 300 mm 60 mm 40 mm 24
In the hanger shown, the upper portion of link ABC is 3/8 in. thick,and the lower portions are each 1/4 in. thick. Epoxy resin is usedto bond the upper and lower portions together at B. The pin at Ais of 3/4 in. diameter while a 3/8 in. diameter pin is used at C. Determine (a) the the average shearing stress on the bonded surfaces at B. (b) the bearing stress in the link at C.