E2.3 Given a two-input neuron with the following weight matrix and input vector: = [3 2] andp [-5 7]", we would like to have an output of 0.5. Do you suppose that there is a combination of bias and transfer function that might allow this? i. Is there a transfer function from Table 2.1 that will do the job if the bias is zero? ii. Is there a bias that will do the job if the linear transfer function is used? If yes, what is it? iii. Is there a bias that will do the job if a log-sigmoid transfer function is used? Again, if yes, what is it? iv. Is there a bias that will do the job if a symmetrical hard limit transfer function is used? Again, if yes, what is it?

E2.3 Given a two-input neuron with the following weight matrix and input vector: = [3 2] andp [-5 7]", we would like to have an output of 0.5. Do you suppose that there is a combination of bias and transfer function that might allow this? i. Is there a transfer function from Table 2.1 that will do the job if the bias is zero? ii. Is there a bias that will do the job if the linear transfer function is used? If yes, what is it? iii. Is there a bias that will do the job if a log-sigmoid transfer function is used? Again, if yes, what is it? iv. Is there a bias that will do the job if a symmetrical hard limit transfer function is used? Again, if yes, what is it?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

For the question (first picture), I set up the circuit below (second picture) but I think there is a mistake in my circuit because the is no current (ID) What is my mistake in the circuit can you tell me
Drive an equation for linear signal conditioning that will convert a sensor output voltage in the spanning the range -1V to 3V into a -5V to 5V span. Also, design a circuit to do the corresponding transformation
If the following data-input waveforms applied to the comparator. the * output in relation to the inputs will be Ag COMP A = BE Bo B. B1 ......
what to answer in, "have have you learned in Fundamentals in Mixed Signals and Sensors". thank you.
Problem 3.41.3- A system is shown below in figure for this system find the transfer function relating displacements y and x and also draw relating mechanical circuit diagram. A fit) K
Electrical Engineering (le:5.D20) You have a 100 mV signal in the frequency range 600 Hz to 700 Hz with which you want to drive a 2002 load. Unfortunately, there is a comparable amount of "line noise" at 60 Hz. You are told that the output impedance of the signal source is 300 2. Design a circuit that will reduce the noise to no more than 20% of the signal and be able to drive your load. You need to specify the power supply voltage and the component values, but you may assume that "reasonable" transistors. you have
Note : Value of K1 = 17; K2 = 49 Show the each equation part and Mention ans same as asking in question. There are must be 2 graphs. Read the 2 pictures clearly and ans all the question. For Example : "Compare T+,T- , Draw the transfer characteristics V0 and V1 " Mention like this then ase the question. formula should be taken from "Operational Amplifier and Linear Integrated Circuits, by Robert F. Coughlin and Fredrick F. Driscoll, 6th Edition, Pearson." this book.
help please
The parameters of an RLC circuit with an input voltage of E(t) are given. R= 20 2, L = 20 H, C = 0.05 F, E(t) = 150 cos 2t V Using the initial conditions I(0) = 0 and Q(0) = 3, plot both the steady periodic current Isp (t) and the total current I(t) = Isp (t) + It, (t). Choose the correct answer below. А. В. С. AI 8- AI 8- AI 8- 8- Isp. Isp 0- 0- 0- 0- 3n 3T 2. 2 'sp Isp