The bent rod ABCD is supported with a ball-and-socket joint at A, a hinge at D and the elastic cable atBwith stiffness k= 100 N/mm. If the 200 kg mass isheld in equilibrium as shown in the figure, determinethe reactions at A and D and unstretched length of thecable EB.0.6 m0.5m0.3 m0.5 m1m0.3 m

Answered: Image /qna-images/answer/9bc92384-6ddd-4912-9537-b081baf96252.jpg

e bent rod ABCD is supported with a ball-and- ket joint at A, a hinge at D and the elastic cable at with stiffness k=100 N/mm If the 200 kg mass is ld in equilibrium as shown in the figure, determine e reactions at A and D and unstretched length of the ble EB. 0.6 m 0.5 m 0.3 m 0.5 m 1m 0.3 m

e bent rod ABCD is supported with a ball-and- ket joint at A, a hinge at D and the elastic cable at with stiffness k=100 N/mm If the 200 kg mass is ld in equilibrium as shown in the figure, determine e reactions at A and D and unstretched length of the ble EB. 0.6 m 0.5 m 0.3 m 0.5 m 1m 0.3 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 1. Rigid member ABC is connected to two elastic bars, as shown in the figure. Bar AD is heated by…

Q: A rigid bar of negligible weight is supported as shown in Figure 2. If W = 100 kN, compute the…

Q: As shown in the figure below, determine the internal loadings at point C. B 0.1 m 0.5 m C A -0.75 m…

Q: The gusset plate is subjected to the forces of three members as shown in (Eigure 1). The forces are…

A: Consider vertical force equilibrium9 - 6sin - Tsin = 09 - 6* - Tsin = 0Tsin = 5.4 ...equation…

Q: Structural Theory

Q: M L1 L2 A L1 4 2 4 B m m m RB Analyze the beam using DIM (origin at A). Assume El to be constant for…

Q: Determine the reactions for the following structure by using Method of Consistent Deformation.…

A: Given data in question Point load Span member length Propped cantilever To find out Reactions

Q: t www h. The steel structure is loaded as shown. hc = 4 m, Lb = 3m, P = 40 KN, E = 200 GPa, Ib Ic=…

Q: The rigid beam is supported by a pin at B and wires AD and CE. (Figure 1) The load P on the beam…

A: Objective: To determine the normal strain in wires AD and CE. Given: Displacement of end A of the…

Q: Q1) A Section of railway track consists of a steel bar of length 15m and cross-sectional area…

Q: 140 mm in the trusses analyies experiment we got the strain Reading as, B Loaden) strain AC 5train…

Q: The beam of flexural rigidity EI is clamped at both ends and subject to a uniformly distributed load…

Q: Consider the construction shown in the figure below. The material has a modulus of elasticity of E.…

Q: Problem The truss is made from three pin-connected members. Determine the maximum average normal…

A: As per guidelines we need to answer only first 3 question, so please repost rest questions…

Q: Determine the reaction of the beam shown. 30kN/m A 5m 15kN/m 2m 50kN 2m

A: Given: Required : Support reactions using method of consistent deformation

Q: 1.5k/pie 10 k-pie 10k-pie +10 pies- A 10 pies- 20 pies 20 pies Prob. 12-11

Q: Find the reactions in the support if F= 228 N 200 mm 510 m B 160 mm 480Tm 240 mm

A: The direction and magnitude of the force vary from time to time due to the different reactions…

Q: Determine the member end moment and reaction for the structure shown below by using kanis method

Q: Determine the degree of determinacy of the structure shown below. Put "-1" if unstable, "O" if…

A: For 2D structure No. Of joint (j) = 7 No. Of member (m) = 11 No. Of support reaction (r) = 2(hinge)…

Q: In the figure shown, the Aluminum member (AC) with a diameter of 1.125in is connected with the steel…

Q: HW2: Analyze the truss shown in the figure, EA is constant for all members

A: Question is based on the truss supported on the hinge and roller support . Loading condition on…

Q: Determine the reactions at rigid supports A and B. A B →10 kN 1 m 2 m

A: Following is the given beam between two rigid supports: Assuming reactions at both support acting…

Q: PLATE NO. 2: DEGREE STRUCTURES Direction: Do as required. Show your solution in neat and orderly…

A: As per guidelines we need to answer only first 3 subparts of questions so please repost rest…

Q: B 1.5 m 1.5 m 3 m 30 30° 4, = 0.5

Q: number of significant digits; the tolerance is +_1 in the third significant digit

A: Step 1: To determine the forces in members BC, BE, and BF of the truss, we can use the method of…

Q: Part A Use the fact that ABC is a three-force member to determine the magnitude of the reactions at…

Q: Calculat reactions at pin support A and edge B, take beam weight 35 Kg 1 т 3 m B 50° A

A: For calculating the reactions equilibrium conditions must be followed: Sum of all the forces among…

Q: Q4: Determine the reactions at the supports A and B shown in the Figure Below due to the applied…

A: Here support A is hinged and support B is roller support. At point A, Vertical reaction VA and…

Q: In the metallic structure represented by the figure below, the load P is 1200 No. What is the…

A: As we can see in the figure, the load P is acting at joint C. To calculate the maximum bending…

Q: Determine the stresses in each bar and the bond reactions.

A: Given in the Question to determine the stress in each bar and bond digram:

Q: roblem 2: A steel hoop, 10 mm thick and 80 mm wide, with inside diameter 1500.0 mm, is heated and…

Q: A rigid bar, the deformation of which may be neglected, is suspended from three rods and loaded as…

Q: * 3m 3m A 3m 4m (10) (5) 20 KN 3m F (10) D (10) B Answers in structures lectures : Analyze the…

A: The given truss is statically determinate truss and can be analyzed using the equations of…

Q: A rectangular polypropylene [E = 6,200 MPa] bar (1) is connected to a rectangular nylon [E = 1,400…

Q: 7. Distributed Loads A beam supports a distributed load as sho (a) Determine the equivalent…

A: To find equivalent load and support reaction

Q: The 465-kg uniform I-beam supports the load shown. Determine the reactions at the supports. Answers:…

A: To determine the reaction at support of the Simply Supported beam.

Concept explainers

Cables

Cables are collections of wires, alternatively referred to as a cord, connector, or plug. They are one or more wires covered in a plastic covering that allows for the transmission of power or data between devices. The earliest use of recognizable electrical cable was the early commercialized telegraph lines. These were iron-made and tedious to produce and install cabling.

Question

The bent rod ABCD is supported with a ball-and-
socket joint at A, a hinge at D and the elastic cable at
Bwith stiffness k= 100 N/mm. If the 200 kg mass is
held in equilibrium as shown in the figure, determine
the reactions at A and D and unstretched length of the
cable EB.
0.6 m
0.5m
0.3 m
0.5 m
1m
0.3 m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

2. From the given figure and data below. Determine the: a. P so that the structure is stable (in equilibrium) b. Draw the FBD of the member BC c. Reaction at A Weight of the member AB and BC = 50kg µ at C= 0.5 1.5 m 3m 1.5 m 30 30° 4, = 0.5
If the supports at A and C are flexible and have a stiffness k, determine the support reactions at A and C. The material has a modulus of elasticity of E.
1. At a temperature of 5°C, a 3-mm gap exists between the end of polymer bar (1) and support A as shown. Bar (1) is 50 mm wide and 20 mm thick (E = 800 MPa, a = 140 x 10-6/°C). Bar (2) is 75 mm wide and 25 mm thick (E = 2.7 GPa, a = 67 x 106/°C). The supports at A and C are rigid (i.e., fixed). Determine: a) the temperature at which the normal stress in bar (2) will be equal to -3.0 MPa, and b) the lengths of the two polymer bars at this temperature. (1) 3-mm gap 50 mm 500 mm B 75 mm 400 mm (2)
Determine the reactions by the method of consistency deformations. Select the reaction at the roller support to be the redundant. 90KN 60KN A 3m 3m D В 3m C E = 200 GPa I= 3.250x10^6 mm4
Problem Classify each of the structures shown in Figures as externally unstable, statically determinate, or statically indeterminate. If the structure is statically indeterminate externally, then dete...
Situation 10: The rigid bar ABC as shown in the figure is pinned supported at B and attached to the vertical two rods. Initially, the bar is horizontal and the vertical rods are stress-free. The temperature in the steel rod is decreased by 40°C. Neglect the weight of the bar Steel L = 910 mm A = 300 mm² E = 200 GPa a = 11.7 x 106/C AT = -45°C 0.5 m + 1.3 m Aluminum L = 1320 mm A 1200 mm² E = 70 GPa a = 23 x 106/C 27. Determine the stress in the aluminum rod 28. Determine the stress in the steel rod 29. Determine the deflection at the point where aluminum rod and bar is attach
278. A rigid horizontal bar of negligible mass is connected to two rods as shown in Fig. P-278. If the system is initially stress-free, determine the temperature change that will cause a tensile stress of 60 MPa in the steel rod. -2 m 2 m 3 m 3 m Bronze A-1200 mm² E 88 GPa x = 18.9 pm/(m. °C) Figure P-278. Steel A = 900 mm? E = 200 GFa Q- - 11.7 m/(m. °C)
A load P will be supported by a structure consisting of a rigid bar ABCD, a polymer [E = 2,300 ksi; α = 2.9 × 10-6/°F] bar (1) and an aluminum alloy [E = 10,000 ksi; α = 12.5 × 10-6/°F] bar (2), as shown. Each bar has a cross-sectional area of 2.00 in.2. The bars are unstressed when the structure is assembled at 30°F. After a concentrated load of P = 56 kips is applied and the temperature is increased to 100°F, determine the normal force in bar (1).
H1