In the figure shown, the Aluminum member (AC) with a diameter of 1.125in is connected with the steel member (CD) of a diameter of 1.625in from point C, these members are restrained by rigid supports at A and D. Find: 1) The values of reactions at supports A + and D 2) The deformation at point C (6) E = 10.4 x 10 psi Eal E = 29 x 10°psi 18Kips 14Kips A D 8 in 10 in 10 in

In the figure shown, the Aluminum member (AC) with a diameter of 1.125in is connected with the steel member (CD) of a diameter of 1.625in from point C, these members are restrained by rigid supports at A and D. Find: 1) The values of reactions at supports A + and D 2) The deformation at point C (6) E = 10.4 x 10 psi Eal E = 29 x 10°psi 18Kips 14Kips A D 8 in 10 in 10 in

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the reactions by the method of consistency deformations. Select the reaction at the roller support to be the redundant. 90KN 60KN A 3m 3m D В 3m C E = 200 GPa I= 3.250x10^6 mm4
The truss shown in the figure is applied with force P= 5kN %3D 1.50 m 1.50 m 150 m 2 m 2 m What is the force in member DE in kN? A.
C: Determine the reactions of the truss shown in Fig, using the method of consistent deformations. Using B, is redundant, EA is constant. 80 kN 60 kN 5 m EA- constant S m 5m 5m
333 of o, and a, if the principal stresses are known to be 20 MPa and -80 935. For the element shown in Fig. P-935, determine the values MPa. 30 MPa 2つ 88 30 MPa Figure P.-935. X
b) A cylindrical rod AB is made of aluminum is connected at B to a brass qylindrical rod BCD as shown in Figure 8. The shear modulus, G of aluminum rod AB is given by 27 GPa and the brass rod BCD of 39 GPa. The torsional reactions, TA and Ts are located at the ends of A and B, respectively. Given the portion CD of the brass rod is hollow and has an inner diameter of 40 mm, examine the angle of twist at A. 60 mm Tg = 1600 N - m 36 mm TA = 800 N m 250 mm 375 mm A 400 mm Figure 8
The assembly in Fig. P-242 consists of a light rigid bar AB, pinned at O, that is attached to the steel and aluminum rods. In the position shown, bar AB is horizontal and there is a gap, A = 5 mm, between the lower end of the steel rod and its pin support at C. Compute the stress in the aluminum rod when the lower end of the steel rod is attached to its support. A 0.75 m O Steel A = 250 mm² E = 200 GPa 1.5 m Figure P-242 Aluminum L = 2 m A = 300 mm² E = 70 GPa B
Calculate the support reactions of the truss shown in Figure E
The force in EC of the truss shown in the figure below is
Calculate the support responses and the bond strengths at the C-joint of the carrier system given in the figure. 6 kNm 4 KN 4 KN 4 kN/m B 1m A 4 m 6 m 10 KN +2m +2m D 3 m F
k * 3m 3m A с 3m 4m (10) (5) 20 KN 3m (10) D (10) B Answers in structures lectures : Analyze the structure as shown in Fig. belows Area = ( ) cm² Ib=100 * 10³ cm4, E = 20*10³ kN/cm² 4m (5) (10) 1 E 2 Members CD, BD, DE, EF, DF & CF are truss members' Member AB is a frame member ·30.6kNim A 15.1 KN 20 KN ETABS Answers: R₁ = 15.103 kN; MA= 30.61 kN.m, FBD = 4.897 KN 4.9 KN
Two links, made up of aluminum and steel, are connected by a hinge joint and an axial load P = 1000N is applied at node 3 as shown in Fig. 1.34. Determine the stresses developed in the two links using the finite element method. Link 1, Steel Link 2, Aluminum E=207 GPa; A=4cm2 E=71 GPa; A=2cm? 3 40 cm 60 cm FIGURE 1.34 Two links subjected to an axial load.
The supports used to support the truss shown below consist of rollers at A and B. The weight of the truss is negligible in relation to the applied loads. Read the following statements and then check the correct alternative. 1)the supports provide exactly the amount of links needed to keep the structure in balance 2)the corresponding reactions involve three unknowns that can be determined through equilibrium equations. 3)although vertical movement is impeded, the truss can move freely horizontally 4)the reactions involve only two unknowns and the lattice is partially linked