e)/ An open rectangular tank (8m) long, (3m) wide and (2m) deep is filled water to depth (1m), the tank is accelerated horizontally with constant value of ( 2 m/sec²), determine: 1- The angle of water surface. 2- The volume of water displacement because the acceleration.

e)/ An open rectangular tank (8m) long, (3m) wide and (2m) deep is filled water to depth (1m), the tank is accelerated horizontally with constant value of ( 2 m/sec²), determine: 1- The angle of water surface. 2- The volume of water displacement because the acceleration.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q: The cross section of oil tank with a slanted bottom as shown in the figure. A rectan door 600 mm by 400 mm in the bottom of the tank. The oil has density of 900 kg/m'. the liquid force R and its location. OP, =0 Poil - 900 kpm 30° R 600 mm 500 mm
6. Rotating Cylinder A 40 cm diameter, 90 cm high vertical cylindrical container is partially filled with 60 cm high of water. Now the cylinder is rotated at a constant angular speed of 120 rpm. Determine the height in the water at r = 10 cm. ANSWER:
Tme left 0:19:26 Consider a 100 kg box which is at the rest. Now, two forces are applied to the box and it starts to move. Consider F1 = 700 N and F2 100 N. Here F1 is a horizontal force and F2 is a vertical force. Find (a) the normal reaction force from ground (N), (b) the distance (m) it slides to reach a velocity of 6 m/s. Take coefficient of kinetic friction to be 0.2. Assume g = 9.81 m/s. F2 F1 (a) the normal reaction force from ground (N) Choose... (b) the distance (m) it slides to reach a velocity of 6 m/s Choose...
Q/ As the hydraulic cylinder rotates around O, the ex- posed length I of the piston rod P is controlled by the action of oil pressure in the cylinder. If the cylinder rotates at the constant rate ở = 60 deg/s and l is decreasing at the constant rate of 150 mm/s, calculate the magnitudes of the velocity v and acceleration a of end B when l = 125 mm. B. 375 mm Answers: v= 545 mm/s a= 632 mm/s2
s [pis. The velocity of the water jet discharging from the orifice can be obtained from v = V2 gh, where h = 2 m is the depth of the orifice from the free water surface. Determine the time for a particle of water leaving the orifice to reach point B and the horizontal distance x where it hits the surface. 2 m 1.5 m
A rectangular container of cross- sectional area 4 m x 1.5 m on an inclined plane with liquid (bc = 0.6 %3D m) as shown in the figure below. You are required to determine the acceleration 'a' along the plane so that the free surface at the edge touches the point b, It may be assumed that the sides of container are high enough so that there is no spilling of liquid. Fo.6m biupid b. Container 4 m x 1.5 m onulo 35
The components of the velocity field is given as u = 0.2 + 0.9x + 0.8y v = -0.5 + 0.9x – 0.9y Calculate the acceleration at point x,y=(0,1) Is this flow field rotational or irrotational? Show. Is this flow compressible or incompressible? Show.
Fluid flows at a velocity V through a horizontal pipe of diameter D. An orifice plate containing a hole of diameter d is placed in the pipe. It is desired to investigate the pressure drop, 4p, across the plate. Assume that Ap f(D, d, p, V) where p is the fluid density. Determine all possible z terms. Show ALL steps. (Figure shows a longitudinal profile section of the pipe). Use FLT Svstem ONLY P1|| P2 Flow
An inverted differential manometer is connected to two pipes A and B whichconvey water. The fluid in manometer is oil of specific gravity of 0.8. For themanometer readings r = 30 cm, s = 20 cm and t = 30 cm, find the pressuredifference between A and B.
in a three-dimensional incompressible fluid flow, the velocity components are:
Q. A block of 150 N is placed on the surface having coefficient of friction 0.4 (shown in figure). What force is required to just enable the block to move. Consider two cases related to force (a) Pushing force (b) Pulling force
Help mee pleasee. Complete solution