6.) A pump is being used to lift water from the bottom tank to the top tank in a cast iron pipe at a discharge (Q). The lengh and diameter of the pipe section from the bottom tank to the pump are (L1) and (d1), respectively. The length and diameter of the pipe section from the pump to the top tank are (L2) and (d2), respectively. Given the values of Q [L/s], L1 [m], d1 [m], L2 [m], d2 [m], calculate total head loss due to friction (i.e., major loss) in the pipe (hmajor loss) in [cm]. Givens: Q=0.906 L1 = 11564.882 d1 = 1.947 L2 = 58.56 d2 = 0.038 Answers: L₁, d₁ (1) 231.294 (2) 114.952 (3) 183.515 (4) 213.901 Pump L₂, dz

6.) A pump is being used to lift water from the bottom tank to the top tank in a cast iron pipe at a discharge (Q). The lengh and diameter of the pipe section from the bottom tank to the pump are (L1) and (d1), respectively. The length and diameter of the pipe section from the pump to the top tank are (L2) and (d2), respectively. Given the values of Q [L/s], L1 [m], d1 [m], L2 [m], d2 [m], calculate total head loss due to friction (i.e., major loss) in the pipe (hmajor loss) in [cm]. Givens: Q=0.906 L1 = 11564.882 d1 = 1.947 L2 = 58.56 d2 = 0.038 Answers: L₁, d₁ (1) 231.294 (2) 114.952 (3) 183.515 (4) 213.901 Pump L₂, dz

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

An incompressible fluid is flowing at a steady rate in a horizontal pipe. From a section, the pipe divides into two horizontal parallel pipes of diameters di and d2 (where d₁ = 4d₂) that run for a distance of L each and then again join back to a pipe of the original size. For both the parallel pipes, assume the head loss due to friction only and the Darcy-Weisbach friction factor to be the same. The velocity ratio between the bigger and the smaller branched pipes is
An orifice meter is a device used to determine the flow velocity and flow rate in a pipe. The meter is connected to a U-tube manometer shown in Figure 2(a). The meter is connected to a U-tube manometer shown in Figure 2(b). Derive the equation for the flow rate, Q in the horizontal pipe.
If you decide to help, please help with all the parts of the question, I'm not sure I understand any of it... :/ The tank shown in the following figure is being filled by Pipes 1 and 2. The water level is to remain constant. A tank of water is open at the top. The tank is filled from above by pipe 1 and pipe 2. Pipe 1 has diameter d1 = 1 in., and fills the tank with water at a velocity of V1 = 2 ft/s. Pipe 2 has diameter d2 = 1.25 in., and fills the tank with water at a velocity of V2 = 1.4 ft/s. Water empties from the bottom of the tank through pipe 3. Pipe 3 has diameter d3 = 1.5 in., and empties water from the tank at an unknown velocity V3. (a) What is the volume flow rate (in ft3/s) of Pipe 1? (b) What is the volume flow rate (in ft3/s) of Pipe 2? (c) What is the volume flow rate (in ft3/s) of water leaving the tank at 3? (d) What is the cross-sectional area (in ft2) of flow for Pipe 3? (e) What is the average velocity (in ft/s) of the water leaving the tank?
An orifice (area = 0.035 ft^2) is placed at the bottom of a cylindrical (diam = 5.93 ft) container. Determine the time (minutes) required for the head to fall from 4.99 ft to 2.35 ft. Use Cc = 0.67, Cv = 0.93. Round of to two decimal places.
The cylindrical tank weights 500 lb. Determine (a) FH, (b) FV, (c) FR and (d) ϴx. Use 2 decimal places in every solved value.
2Q. A flow field is defined by u = 2y, v = xy. Derive expressions for the x and y components of acceleration. Find the magnitude of the velocity and acceleration at the point (2,3). Specify units in terms of L and T.
An incompressible fluid is flowing at steady rate in horizontal pipe. From a section, the pipe divides into two horizontal parallel pipes of diameter (d, and d₂) (where d₁ = 4d₂) that run, for a distance of L each and then again join back to a pipe of the original size. For both the parallel pipes, assume the head loss due to friction only and the Darcy-weisbach friction factor to be same. The velocity ratio between bigger and smaller branched pipe is.
Consider a pond of circular shape, radius R and width B (the width measured in the direction normal to the plane of the sheet). A pipe emerges from the bottom of the pond connected to a pump. This equipment sucks water at a flow rate Q = Kh2, where K is a constant and h(t) the height of the liquid contained in the pond at any instant t. Assume that the pond is initially full (h(0) = R). Determine algebraically the time T it takes for the system to empty.
The brake drum is attached to a larger flywheel that is not shown. The motion of the brake drum is defined by the relation θ = 36t − 1.6t^2 + 2t^3, where θ is expressed in radians and t in seconds. Determine (a) the angular velocity at 10sec. (b) the number of revolutions executed by the brake drum before coming to rest.