e 3 m high is fixed at the base. It is 6mm thick and its outside diameter is 300mm. The pole is subjected to a torque and a lateral force at the free end. Given: Torque, T = 25 kN-m Lateral Force, N = 3 kN Shear Modulus of Elasticity = 78 GPa Allowable Shear Stress = 60 MPa   1. What is the maximum shear stress (MPa) at the outside surface of the pole due to the torque, T? 2. What is the angle of twist (degree) due to the torque? 3. Find the maximum flexural stress (MPa) at the base of the pole due to the lateral forc

Q: = A solid steel cylinder with diameter of 40 mm and a shear modulus of G = = 75 GPa has fixed ends.…

A: Step 1: Step 2: solution is given above Step 3: Step 4:

Q: 4 - A rectangular block is loaded with a 180 kN axial force and a moment M, as shown in the figure.…

A: Given data:-  Axial force =180 kN the maximum allowable tensile stress = 50 MPa To find:- the…

Q: A point On a free surface of a machine point (E = 214Gpa, G= 83Gpa) the stress state is shown on the…

A: GIVEN :- E = 214Gpa G= 83Gpa σy=15 MPaσx=-30 Mpaζxy=25 MPa

Q: 2. A hollow generator shaft of 180-mm outer diameter and 120-mm inner diameter carries a torque T 40…

A:

Q: 2. The component shown always breaks at point C, which is just to the right of the contact point of…

A: The component always breaks at point C, which is just right of the contact point of the roller at B.…

Q: Find the longitudinal stress in the tank.

A: To Find the longitudinal stress.

Q: The beam is supported by double-shear pins at A, B, and C. The radius of all the pins are r = 8 mm.…

A: Find outDetermine the magnitude of the normal force in rod BC, .Determine the magnitude of the…

Q: A 9 cm diameter solid aluminum post is subjected to a horizontal force of V= 8.1 kN and a…

A: Given, A 9 cm diameter solid aluminum post is subjected to a horizontal force of V= 8.1 kN and a…

Q: Determine the torsional shear stress in the shaft section AB and BC. There is a fixed support at C…

A:

Q: A rod is made from two segments: AB is steel and BC is brass. It is fixed at its ends and subjected…

A: Torque at the joint of both shaftsDiameter of the steelBecause the end reactions are same hence the…

Q: re= 3cm 300m 20m

A: When a shaft is subjected to torque, shear stress produces in the shaft. The torsion equation is…

Q: Q2: The rigid beam shown in fig2 is held by two vertical rods at A and C.If a 60 KN load is applied…

A:

Q: An idealized model of a thin-walled convertible car body cross-section is shown in figure Q16. The…

A:

Q: Consider a two-component rod fixed at the left end. The first component (on the left, positioned…

A:

Q: Find the stress in ksi developed in the pipe due to a temperature rise of 83 degrees F.

A: Length of the pipe is L=12 ft Temperature rise in the pipe is ∆T=83 °F Modulus of elasticity of the…

Q: The tube has a length of 2 m and is made of the material with the properties provided in the…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.