Dynamics Lab is A 7.75-kg uniform disk developed in the attached to the 4.85-kg slender rod AB by means of frictionless pins at B and C. The assembly rotates in a vertical plane under the combined effect of gravity and of a couple M that is applied to rod AB. Knowing that at the instant shown, the assembly has an angular velocity of 6.00 rad/s and an angular acceleration of 25.0 rad/s², both counterclockwise, determine; Determine: (a) the couple M (b) the force exerted by pin C on member AB

Dynamics Lab is A 7.75-kg uniform disk developed in the attached to the 4.85-kg slender rod AB by means of frictionless pins at B and C. The assembly rotates in a vertical plane under the combined effect of gravity and of a couple M that is applied to rod AB. Knowing that at the instant shown, the assembly has an angular velocity of 6.00 rad/s and an angular acceleration of 25.0 rad/s², both counterclockwise, determine; Determine: (a) the couple M (b) the force exerted by pin C on member AB

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A rigid beam BC is suspended by rods AB and CD as shown in the figure. Rod AB is made in from aluminum while rod CD is made from steel. Determine the location/placement of the 75kN concentrated load within the beam BC such that the rigid beam BC will remain horizontal after deflection. Determine the axial deformation of rods AB and CD.
In the beam depicted above, ?A is a fixed support. The magnitude of ?=365?/?W=365N/m, ?=60?P=60N and all lengths denoted by ?=1.5?a=1.5m. The system is in equilibrium. Using the given sign convention, answer the following questions. a) Calculate the vertical component of the external reaction at ?A in ???????Newtons. b) Calculate the horizontal component of the external reaction at ?A in ???????Newtons. c) Calculate the moment component of the external reaction at ?A in ??????Newton ??????metres. d) Calculate the shear force at point ?B in ???????Newtons. e) Calculate the bending moment at ?B in ??????Newton ??????metres. f) Calculate the shear force at point ?D in ???????Newtons. g) Calculate the bending moment (absolute value) at ?D in ??????Newton ??????metres. h) Calculate the shear force at point ?E in ???????Newtons. i) Calculate the bending moment at ?E in ??????Newton ??????metres. j) Calculate the shear force at point ?H in…
Two beads are sliding freely on a horizontal rod. Use the following conditions. mA = 3 kg m₂ = 1 kg e=0.9 VA = 1 m/s Va = -3 m/s a. Determine the final velocity of both beads. b. Determine the average interaction force, F between the beads if the duration of the impact is 0.005 seconds Vg m ma
Beam AC is in equilibrium with loading 100 N at B shown in the figure when β = 45. Determine the unknown forces Ax and Ay at A in x and y direction and Rc perpendicular to the beam AC in y’ direction at C by using the equilibrium equations: ∑ ???= 0 ; ∑ ??y= 0; and ∑ ???= 0 where o is an arbitrary point. (you have three equations to solve three unknowns)
the forces on the gusset plate of a joint in a bridge truss act as shown. shown. Determine the values of P and F to maintain equilibrium of the joint ж 1000 в b to 300016 Jir Fine
The portion AOB of a mechanism consists of a 400-mm steel rod OB welded to a gear E of radius 120 mm which may rotate about a horizontal shaft O. It is actuated by a gear D and, at the instant shown, has a clockwise angular velocity of 8 rad/s and a counterclockwise angular acceleration of 40 rad/s². Knowing that rod OB has a mass of 3 kg and gear E a mass of 4 kg and a radius of gyration of 85 mm, determine (a) the tangential force exerted by gear D on gear E, and (b) the components of the reaction at shaft O. 120 mm 00. On If 400 mm
The board rests on the surface of two drums. At the instant shown, it has an acceleration of 0.44 m/s? to the right, while at the same instant points on the outer rim of each drum have an acceleration with a magnitude of 4.7 m/s². If the board does not slip on the drums, determine its speed in m/s due to the motion. r = 11.3 in a r
Figure 1: For the frame shown, determine the magnitude of the pin reaction at B. Neglect the weight of the frame. (2 decimal point, indicate the answer in kN. Ex: 3.87kN just encode 3.78) * 2 m 1.8 m 3 m 15 kN/m A 12 kN/m
A 0.15-kg glider is moving to the right on a Frictionless, horizontal air frack with a speed oF 0-8 ms it has a head-on collision with a 0.3- kg glider that is noving to the left with a sped f 2.2 m/s. Find the firal velocity (magnitide & direction) glider ir the co\lision is elastic. each OF
6/47 A block of mass mo is placed between the vertical wall and the upper end A of the uniform slender bar of mass m. If the coefficient of static friction is µg be- tween the block and the wall and also between the block and the bar, determine a general expression for the minimum value 0min Oof the angle 0 for which the block will remain in equilibrium. Evaluate your expression for the conditions µ = 0.5 and %3D т (a) mo 0.1, m (b) mo 1, and m (c) mo 10. %3D For each case, state the minimum coefficient of sta- tic friction (u)B necessary to prevent slippage at B. Ans. (a) 0min = 61.2°, (µ,)B = 1.667 (unusual!) (b) 0min = 45°, (µ)B = 0.667 (c) 0min = 10.30°, (µ,)B = 0.0952 %3D %3D %3D %3D %3D mo m (Ha)B Problem 6/47
The structure shown consists of two uniform legs, each having the same mass per unit length of 10.3 kg/m. The leg BC connects to the other leg via a pin-joint at B, such that free rotation at B is possible. If the smallest value of the angle 0 for which the structure will remain in static equilibrium is 58.7 degrees (i.e. slipping does not occur at either contact point A or C), calculate the coefficient of static friction, assuming the same value at both contact points A and C. B