A rigid beam BC is suspended by rods AB and CD as shown in the figure. Rod AB is made in from aluminum while rod CD is made from steel. Determine the location/placement of the 75kN concentrated load within the beam BC such that the rigid beam BC will remain horizontal after deflection. Determine the axial deformation of rods AB and CD.

Q: In a simply-supported beam loaded as shown below, the maximum bending moment in Nm is 1000 mm 500 mm…

A:

Q: Both portions of the rod ABC are made of an aluminum for which E= 70 GPa. Knowing that the magnitude…

A: Given : E = 70 GPa This is a problem of solid mechanics where we are asked to determine : a) The…

Q: 1.3.2

A:

Q: A circular shaft AB of radius Ras shown in the figure below is subjected to torsion T at the free…

A:

Q: 100 mm 25 mm 125 mm M. 75 mm The beam is subjected to an internal moment of M = 3 kNm. 25 mm 75 mm…

A:

Q: 1. The weight W = 2kN in Figure1. What is the total reaction at A in kN? 30° W 600 mm 600 mm Figure…

A:

Q: A prismatic fixed-fixed beam, modelled with a total lumped-mass of 10 kg as a single degree of…

A:

Q: A prismatic bar is fastened between two rigid walls A and Band subjected to loads as shown in…

A: RA + RB =  13.6 + 22.7  RA + RB =   36.3 kNn

Q: p N/m w N/m 75 mm 125 mm 100 mm R1 = 1350 N R2 = 2700 N Figure M03

A:

Q: A wooden beam is fabricated from three boards, which are fastened together with screws as shown. The…

A: Introduction- The Timber Beam is a one-of-a-kind block that serves as a framework wall but takes up…

Q: The steel plate shown below is put in into a rigid chamber, such that spacings of size s 0.00188 m.…

A:

Q: If the Force of members AB, AC, and BC is 7kN, 6.06kN, and 0.37kN, what is the magnitude of the…

A: Given Data  Force in member  FAB = 7 KN  FAC = 6.06 KN  FBC = 0.37 KN  Find force in member CD and…

Q: Figure P24.25a shows a uniform beam subject to a linearly increasing distributed load. The equation…

A: Given Parameters: L = 600 cm E = 50000kn/cm2 I = 30000 w0 = 2.5 kn/cm

Q: 1. Given that the value of P on the figure below is equal to 15 kN which is applied to the…

A: To Determine Stress in each rod segment.

Q: At a temperature of 34°F, a 0.06 in. gap exists between the ends of the two bars shown. Bar (1) is…

A:

Q: A steel column of length 6 m forms part of a support structure and is subjected to an axial…

A: It is required to determine the area. A=BD-bd=75 mm×125 mm-67.5 mm×110 mm=1950 mm2 It is required to…

Q: A prismatic beam P-Q-R of flexural rigidity El = 1x104 kNm2 is subjected to a moment of 180 kNm at Q…

A:

Q: The maximum bending moment induced in the beam loaded as shown in figure is KM, then the value of Ik…

A:

Q: Draw the Free Body Diagram for the structure below. 3'-0" A7 Pin support 800 lb 5' 0" 60⁰ 500 lb…

A:

Q: For the loaded beam shown below , E

A:

Q: The beam shown below is suspended from two steel rods as shown and is initially horizontal. The…

A: Step 1

Q: A Given the FLEXURAL beam shown=6000 RIGIDITY of the KN.m^2, find the :deflection at the roller…

A: Roller support is a support condition in which vertical movement is restrained while the rotation…

Q: Q.1: A shaft composed of segments AB, BC is fixed between the two walls at A and C and loaded as…

A: Given that: A composite shaft as shown -

Q: Q1) A Section of railway track consists of a steel bar of length 15m and cross-sectional area…

A:

Q: The steel shaft is formed by attaching a hollow shaft o a solid shaft. Determine the maximum torque…

A:

Q: Q.4.b. A compound bar is made up by connecting a steel member and a copper member rigidly fixed at…

A: Area of copper bar=A Area of steel bar= 2A for one half and A for second bar coefficient of thermal…

Q: The uniform A-36 steel bar in Fig. 4-5a has a diameter of 50 mm and is subjected to the loading…

A:

Q: In the set of beams shown below, the reactive force at support A is: 60 N 40 N 2 m 1.75 m 60 N D A C…

A:

Q: A cantilever beam of length L and depth h is subjected to a uniform temperature rise along its…

A: Cantilever beam -  Let t1 be temperature at the top of the beam. Let t2 be temperature at the…

Q: We15 KN/m P-30

A:

Q: The aluminum bar ABC has a cross-sectional area of 20 mm2 is supported by a pin at A and a steel…

A: Solution; Given that; Cross-sectional area of aluminium bar=20 mm2 P=50 KN Cross-sectional area of…

Beams

In structural engineering, a beam is a component made of a variety of materials (including steel alloys, and wood) that can resist loads applied laterally to the beam axis. Members, elements, rafters, shafts, and purlins are all terms used to describe beams.