During the first stage of triaxial test when the cell pressure is increased from 0.10 N/mm² to 0.26 N/mm2, the pore water pressure increases from 0.07 N/mm² to 0.15 N/mm². What is the value of the Skempton's pore pressure parameter B? "

During the first stage of triaxial test when the cell pressure is increased from 0.10 N/mm² to 0.26 N/mm2, the pore water pressure increases from 0.07 N/mm² to 0.15 N/mm². What is the value of the Skempton's pore pressure parameter B? "

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The thin square plate shown is uniformly deformed such that , +1.360 ut. , -628 ut, and y=+1.285 urad. Determine the normal strain ,, in the plate. 60 mm -276 με Ο 351 με -179 ut -254 HE -233 με x
Some measurements on a blood sample at 37 °C (98.6 °F) indicate a shearing stress of 0.540 N/m² for a corresponding rate of shearing strain of 192 s¹. Determine (a) the apparent viscosity of the blood and (b) its ratio to the viscosity of water at the same temperature. (a) Ublood= (b) Hblood/HH2O= N*s/m²
A boiler of 1.6 m diameter is made of a 20-mm thick plate. What will be the permissible steam pressure in the boiler in the maximum tensile stress in the plates must NOT exceed 80 MPa?
Problem 4. Two strain gages are mounted on a thin-walled cylindrical pressure vessel. One strain gage is oriented parallel to the longitudinal axis of the thin-walled cylindrical pressure vessel while the other strain gage is perpendicular to the first. The tank has radius r= 20 in. and wall thickness of t= 0.4 in. It is made from a material that has %3D Young's Modulus E = 15x10® psi and Poisson's Ratio v =0.31. The strain gages in. report the following after the tank is pressurized: & = 133.0µ and ɛy = 591.5µ. in. in. in. E (& + v&µ) and ơ E From Hooke's Law: 0 (1-v*) (1-v²) Determine: Gage Pressure p
Boundary Layer Theory A thin flat plate having dimension 0.5 m x 0.7 m in size settles in a large tank of water with a terminal velocity of 0.12 m/s. The viscosity and density of water are given as 10-3 N-s/m² and 103 kg/m³. Then find the weight(N) of the plate? Given thickness of plate is negligible.
Find the value of porosity e=0.43
9) Suppose in the high temperature DSR test in the RTFO-aged condition, the measured G* was 2.2 kPa, while the rutting parameter was 2.1 kPa. Answer the following: a. Does the tested binder meet the SPV criteria for RTFO binder in the DSR rutting test? b. Although not mentioned here, back-calculate and report the phase angle.
In Triaxial test, which of the following parameters do not need to be recorded the confining pressure specimen diameter changes the generated pore pressure the axial force
Some measurements on a blood sample at 37 °C (98.6 °F) indicate a shearing stress of 0.550 N/m² for a corresponding rate of shearing strain of 202 s¹¹. Determine (a) the apparent viscosity of the blood and (b) its ratio to the viscosity of water at the same temperature. (a) Ublood= 0.002723 N*s/m² (b) Hblood/HH2O= 3.934
Two dimensional stress system on a block made of a material with Poisson's ratio of 0.3 is shown in fig. A B 60 N/mm² The limiting magnitude of the stress so as to result in no change in length AB of the block N/mm². is
The thickness of the laminar boundary layer on a flat plate at a point A is 2 cm and at a point B, Im downstream of A, is 3 cm. What is the distance of A from the leading edge of the plate?