a) compute the magnitude of the stress at point P, when the externally applied stress is 140 MPa. b) how much would the radius of curvature at the point P need to be increased to reduce the stress by 25%

a) compute the magnitude of the stress at point P, when the externally applied stress is 140 MPa. b) how much would the radius of curvature at the point P need to be increased to reduce the stress by 25%

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Knowing that the maximum allowable stress is 43 MPa, determine the magnitude of the largest moment M that can be applied to the component shown. M B M' A qu 36 mm 150 mm 45 mm 135 mm The magnitude of the largest moment M that can be applied to the component is 14.41 kN.m.
44 ksi 3 ksi 70 S ksi Given the state of stress above (ignore 70° plane): calculate the maximum shear stress, maximum principal stress and minimum principal stress in this order. Choose only one answer.
A steel rod 3 ft long with a cross-sectional area of 0.3 in.² is stretched between two fixed points. The tensile force in the rod is 1300 lb at 40°F. Using a = 6.5 x 10-6 / °F and E = 29 x 106 psi, calculate the temperature at which the stress in the rod will be (a) 10 ksi; and (b) zero.
The rectangular plate is subjected to force P that causes elongation in the horizontal direction and shrinking in the vertical direction as shown with the dashed line in the figure. Assume a = 550 mm, Δx = 2 mm, and Δy = 1.1 mm. Determine the shear strain γxy at point A? Determine the shear strain γnt at point A? In micro rad What is the normal strain in the x-direction? What is the normal strain in the y-direction? What is the normal strain in the n-direction? Answer in clear way please
2. For the given state of stress shown in figure 2. 48 MPa Figure 2. a. Construct Mohr's circle for this plane stress. ||₁6 16 MPa 60 MPa Determine the principal stresses and principal planes.
Please provide solution for this question and explanation.
At a point on the surface of a generator shaft, the stresses are shown on the stress element in the figure. Using Mohr's circle, determine the following: • The stresses acting on an inclined at an angle 0= 45° CCW • The principal stresses • The maximum shear stresses. • Show all results on sketches of properly oriented elements. 0 10 MPa 50 MPa 40 MPa
please box the final answer
Q: A piece of material is subjected to tensile stress of 70 N/mm² in one direction and a compressive stress of 50 N/mm² in a direction at right angles to the previous one. Find fully the stresses on a plane the normal of which makes an angle of 40 degree with the 70 N/mm2 stress.
Part B - The internal reaction at B Assume that the axial member is in equilibrium and the applied forces are an unknown load F₁. F = 5 kN. F₂ = 3 kN, and F₁ = 2 kN. Calculate the internal resultant normal force at section B. Express your answers to three significant figures in kN. ▸ View Available Hint(s) PB = Submit ΨΕ ΑΣΦΠ Part C - The internal reaction at D PD = Submit D] ΑΣΦΩΤ vec Assume that the axial member is in equilibrium and the applied forces are an unknown load F₁, F₂=5 kN. F₂ = 3 kN. and F₁ = 2 kN. Calculate the internal resultant normal force at section D. Express your answers to three significant figures in kN. ▸ View Available Hint(s) Part D - The average normal stress µA vec Value P * ? ? Units KN 2 ? Suppose the axial member has a circular cross section with a diameter of d = 16 cm at section B and a diameter of dp = 8 cm at section D. What is the average normal stress in the section with the maximum magnitude stress? Express your answer to three significant figures…
4. A uniform bar with an area of o.25 in- is pulled between two points. The tensile force at a temperature of 21.11°C is 1200 lb. What will be the stress at -17.78°C? At what temperature will the stress be zero? Assume a = 6.5 × 106 in/(in-°F) and E = 29 × 10ʻ psi. %3D %3D
The stresses on two perpendicular planes through a point in a body are 160 MPa and 100 MPa, both compressive, along with a shear stress of 80 MPa. What is the normal stress on a plane inclined at 30° to the plane of 160 MPa stress? (a) -42.4 MPa (b) -75.7 MPa (c) -59.1 MPa (d) -86.3 MPa