Draw with suitable scale tongitudinal section for raft foundation according to the following data: • Dimensions of foundation are (25 x 25 x 0.5) m with two layers of reinforcement (O 25 @ 250 mm in both directions). • Dimensions of each column are (400 x 400) mm with 4 bars Ø 18 mm and stirrups Ø 10 mm @ 250 mm. • Spans between columns are 4 m (center to center) in both directions. • Depth of foundation is 500 mm from N.G.L. Enhance your drawing with full details and dimensions.

Draw with suitable scale tongitudinal section for raft foundation according to the following data: • Dimensions of foundation are (25 x 25 x 0.5) m with two layers of reinforcement (O 25 @ 250 mm in both directions). • Dimensions of each column are (400 x 400) mm with 4 bars Ø 18 mm and stirrups Ø 10 mm @ 250 mm. • Spans between columns are 4 m (center to center) in both directions. • Depth of foundation is 500 mm from N.G.L. Enhance your drawing with full details and dimensions.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Give me right solution according to the question.
A footing of size 2.5 m x 2.5 m and 500 mm thick resists characteristic axial loads of 800kN dead and 300 kN imposed from a 400 mm square column. The safe bearing pressure on the soil is 230 kN/m2 and the characteristic material strengths are fcu = 35 N/mm2, fy=460N/mm2. Density of concrete is 24 k N/m3. Cover to all reinforcement is 50 mm. Determine the design load b) Check whether the base pressure is safe c) Design the bending reinforcement, assuming 16 mm diameter bars.
Reinforcement concrete
A square spread footing supports a square tied column as shown. Assume that the reinforced concrete is normal weight (24 kN/m3) and = 1.00 (NSCP C101-15 Table 419.2.4.2). The column has a height of 3.5 meters. 1. Check NSCP code requirements for the reinforcement: (a) longitudinal bar clear spacing, (b) steel ratio, (c) minimum number of bars, (d) minimum lateral tie size, (e) spacing of ties, and (f) arrangement of ties. 2. Calculate the plan dimensions (L m x L m)of the spread footing. Assume a trial thickness of the footing H = 750 mm. 3. Calculate the effective depth d (mm) considering punching shear (two-way shear).
a square footing 2.4 m x 0.34 m thick supports a 300 mm square column at its center. column loads are at service conditions dl = 346 kn, ll = 231 kn, fc' = 21 mpa, and fy = 415 mpa. concrete cover to the centroid of steel reinforcement is 100 mm. calculate the nominal one way shear stress in the slab
X=30
A nominal 6x6 timber (5 1/2 x 5 1/2 actual) is used as a short foundation post. It must support a load of 10,000 pounds. Determine the average axial stress found in the post.
Geotechnical engineering -2 (foundation engineering) Solve the following problem with complete solution thank you so much here is 5:09pm i need it by 5:50pm thanks! :)
An engineer is responsible to design a safe and stable foundation that can transmit the loaduniformly under the structure. You are assigned to design a foundation for a double- storeyreinforced concrete shop house in Batu Pahat, Johor. FIGURE Q4(a) and FIGURE Q4(b) showthe layout plan and artist illustration for the building, respectively. The soil condition of theconstruction site is soft clay with a low bearing capacity value. Briefly explain FIVE (5) factors that need to be considered in the design
QUESTION 2 A square column with side dimension of 20 mm rests on top of a timber footing. It is determined that the column carries an axial load of 591 kN. If the punching strength of concrete is 19.86 MPa, determine the minimum thickness (mm) of the footing.
A 6ft x 6ft foundation is subjected to an axial load Q = 225k and a moment M = 100k ft. The depth of footing is 5ft. The soil unit wt is 125pcf, phi = 32deg and c=1000psf Find: 9min qmax e L' qult using the general BC equation
Answer the following problem and show your solution 1. A 400 mm concrete wall supports a DL= 200 kN and LL =146 kN. The allowable bearing pressure is 216 kPa at the level bottom of the footing which is H=1.2m below the grade. Weight of concrete is 24 kN/m^3 and that of soil is 16kN/m^3. Thickness of footing is 300mm with an effective depth of 225mm. use load combination of U=1.4DL+1.7LL f'c-28 MPa, fy=248MPa. Use 28 mm diameter reinforcing bars. Normal weight concrete λ=1.0 a. Determine the effective soil pressure b. Find the width of the wall footing c. Compute the spacing of 28mm diameter steel reinforcement