A spread foundation with the bottom dimension of 2mx1.2m, it is known that the upside column size is 500mmx500mm, the center load from the ground surface is 500kN, the effective height ho is 0.465mm, and the ultimate tensile strength of concrete is 1.1MPa. Question: Try to draw the calculation diagram and calculate the punching shear force of the spread F₁ ≤0.7Phpfamho, and Php = 1.0 foundation. (Tips:

A spread foundation with the bottom dimension of 2mx1.2m, it is known that the upside column size is 500mmx500mm, the center load from the ground surface is 500kN, the effective height ho is 0.465mm, and the ultimate tensile strength of concrete is 1.1MPa. Question: Try to draw the calculation diagram and calculate the punching shear force of the spread F₁ ≤0.7Phpfamho, and Php = 1.0 foundation. (Tips:

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A square column with side dimension of 40 mm rests on top of a timber footing. It is determined that the column carries an axial load of 621 kN. If the punching strength of concrete is 17.40 MPa, determine the minimum thickness (mm) of the footing.
5 A square footing 2.4 m x 0.35 m thick supports a 300 mm square column at its center. Column loads are service conditions: DL = 372 kN LL = 293 kN f’c = 21 MPa fy = 415 MPa Concrete cover to the centroid of steel reinforcement = 100 mm Calculate the maximum ultimate bending moment in the slab. Write your final answer as whole number with the unit of kN-m.
A rectangular footing 2.1 m x 3.2 m x 0.37 m thick supports a 300 mm square column at its center. Column loads are service conditions: DL = 363 kN LL = 291 kN f'c = 21 MPa Fy = 415 MPa Concrete cover to the centroid of steel reinforcement = 100 mm Calculate the nominal punching shear stress in the slab. Write your final answer with 2 decimal places if the unit is MPa.
a rectangular footing 2.3 m x 3.3 m x 0.31 m thick supports a 300 mm square column at its center. column loads are service conditions:DL = 385 kN LL = 292 kN f'c = 21 MPa fy = 415 MPa Concrete cover to the centroid of steel reinforcement = 100 mm calculate the nominal punching shear stress in the slab. write your final answer with 2 decimal places if the unit is MPA.
A square column with side dimension of 40 mm rests on top of a timber footing. It is determined that the column carries an axial load of 621 kN. If the punching strength of concrete is 17.40 MPa, determine the minimum thickness (mm) of the footing.
Question 46 A singly reinforced rectangular beam 300 mm wide and 600 mm deep is subject to a factored shear force Vu = 396 kN at the critical section for shear. Tensile bar centroid is 70 mm from bottom of the beam. Calculate the required nominal shear strength (kN) of 10-mm-dia. the stirrups if lightweight concrete strength is 24 MPa. Write your answers in 2 decimal places only.
Determine the maximum aggregate size (MAS) for an 18" wide foundation wall that has two layers of rebars. It is comprised of number 4 rebar at 6" on center in the horizontal direction and number 6 rebar spaced at 2" on center in the vertical direction. It has 1.5" clear cover on the side of the wall
A singly reinforced rectangular beam 300 mm wide and 600 mm deep is subject to a factored shear force Vu = 384 kN at the critical section for shear. Tensile bar centroid is 70 mm from bottom of the beam. Calculate the required nominal shear strength (kN) of 10-mm-dia. the stirrups if lightweight concrete strength is 26 MPa. Write your answers in 2 decimal places only.
What is the suitability of using the Boussinesq equation for determining subsurface stresses in a foundation analysis?
QUESTION 2 A square column with side dimension of 20 mm rests on top of a timber footing. It is determined that the column carries an axial load of 591 kN. If the punching strength of concrete is 19.86 MPa, determine the minimum thickness (mm) of the footing.
Determine the required reinforcement for L – section beam to resist torsion ? = 10??. ? with the following dimensions; depth of slab = 100 ?? width of flange = 900 ?? width of web = 200 ?? depth = 455 ?? Consider concrete class ?30 and high yield steel ?460 for main Reinforcement and S250 For stirrups
30 A rectangular footing 2.3 m x 3.6 m x 0.38 m thick supports a 300 mm square column at its center. Column loads are service conditions: DL = 306 kN LL = 241 kN f’c = 21 MPa fy = 415 MPa Concrete cover to the centroid of steel reinforcement = 100 mm Calculate the nominal punching shear stress in the slab. Write your final answer with 2 decimal places if the unit is MPA.