Determine the maximum aggregate size (MAS) for an 18" wide foundation wall that has two layers of rebars. It is comprised of number 4 rebar at 6" on center in the horizontal direction and number 6 rebar spaced at 2" on center in the vertical direction. It has 1.5" clear cover on the side of the wall

Q: #5 DOWELS @ 12" O.C. ALTERNATING DIRECTIONS #4 REBAR @ 12" O.C. 5 EACH #4 CONT. REBAR 3' 1'-3" 12'…

A: Given Data, Continuous bar = 5 each #4 Lateral bar = #4 @ 12 inch on center Dowel bar = #5 @ 12 inch…

Q: Identify types of each slab panel and label the shear force coefficient for loading distribution…

A:

Q: Please answer with complete illustration. A cantilever slab has a span of 2.40 m. It is 150 mm thick…

A: Loads are external forces that can produce stress, deformation, displacement, and acceleration in a…

Q: A square footing 2 m x 0.36 m thick supports a 300 mm square column at its center. Column loads are…

A:

Q: A square footing 2.3 m x 0.35 m thick supports a 300 mm square column at its center. Column loads…

A: The thickness of footing is designed based on the  Bending moment acting along the critical…

Q: 15' 30' 20 W = 4' 51 3' 9' 9' 10' 15' 18' 2. The width of the foundation wall shown in problem 1 is…

A:

Q: Using concrete with a design strength of 2000 psi and grade 40 bars with a yield strength of 40 ksi,…

A: Given Design strength, fck=2000 psi =13.8 MPa Wall thickness =10in=254mm Dead load, DL=5000…

Q: Example: Calculate the masonry works above water proofing level for the plan shown in Figure:…

A:

Q: ŠITUATION. A square footing 2.4 m x 2.4 m x 0.45 m thick supports a rectangular column 0.35 mx 0.40…

A:

Q: Column Footings For Problems 12.7 to 12.12, design square single-column footings for the values…

A: Following is the given data : Rebar = #7, CC = 3 in, d = thickness - 1.5db - CC Assume footing…

Q: a. Calculate the total area of this floor. b. Determine the following slab weights. (Note:…

A: Given: floor dimension: (3+30+30+3) x (3+25+25+25+3) = 66 ft x 81 ft Beam dimension, B2: 12'' wide x…

Q: A symmetrical hollow concrete masonry unit, with a cross-sectional area asshown in Figure P8.8, is…

A: Given: The compressive strength at failure P, is 329 kN. Calculation: The figure is shown below,

Q: 2. In a one-way slab 50% of the #8 tension epoxy coated bars are going to be spliced. At the…

A: The diameter of main bars is db= 1 in.  (Imperial Bar size of #8)The rebars are epoxy coated…

Q: sections shown if f = 4000 psi and f, = 7.5àfe, normal-weight %3D concrete, à = 1.0. 24 in. 4 in. 15…

A:

Q: square footing 2.2 m x 0.31 m thick supports a 300 mm square column at its center. Column loads are…

A:

Q: Explain Procedures for bracing excavation sheeting..

A: Procedure of the Bracing Excavation:

Q: Determine the weight of rebar reinforcement for the tunnel concreting works per specified diameter,…

A: Following are the given information. a. Rebar are assumed at 150 kg per cubic meter of concrete. b.…

Q: For rebar works computation: If a flat concrete member of dimensions 3.0m x 3.0m x 0.5m (occurring 4…

A:

Types of Foundation