Draw the small-signal equivalent model of the following circuit. Using the model, and assuming the transistor parameters of M₁ and M2 to be identical and AM1 = AM2 = 0, a) Find the relation between the transconductance, gm of M₁ and M₂. b) Find the relation between the input voltage v; and Vgs1. c) Find the output voltage, vo. d) Find the small signal voltage gain, Av.

Draw the small-signal equivalent model of the following circuit. Using the model, and assuming the transistor parameters of M₁ and M2 to be identical and AM1 = AM2 = 0, a) Find the relation between the transconductance, gm of M₁ and M₂. b) Find the relation between the input voltage v; and Vgs1. c) Find the output voltage, vo. d) Find the small signal voltage gain, Av.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Two PNP transistors are connected to form a Darlington pair to create a single stage amplifier. Both transistors have the same B. Assume that is large such that 3+ 1 ~ B. Vcc 028² 028 9m2 RL 2+9m2 RL VIN PNP Darlington Pair Used as an Amplifier 1. If the Darlington pair is to be treated as a single transistor, what is the overall 3 if the "emitter current" is IOUT? OB² 9m2 Rp 1+9m2 RL RL 9m2 RL iOUT 2. Calculate the approximate expression for Ay. User1 and gm1 for the parameters of Q1 while 2 and for the parameters of Q2. Assume VA → ∞ for both transistors. 9m2 -9m2 RL 2 VOUT
Q1. (a) Using the hybrid-pi model with early voltage effect, compute the small signal voltage gain, Av, input resistance and output resistance for the CE BJT amplifier shown below. Vec = 12 V B=100 VELON) = 0.7V V = 100V R = 93.7k2 %3D E R=6 kN Rg=0.5 k2 C, E R2= 6.3 k2 Figure Q1(a)
Since the transistors used in the circuit are b=200 and r0= ∞(endless);A) By analyzing the DC for each amplifier floor separatelyre1, re2 find resistance values.B) Draw the AC equivalent circuit of the amplifier circuit.C) For each floor Zi=?, Z0 =?D) For each amplifier floor Av1, Av2 find the tension gains.E) Avl find Vl voltage value by finding voltage gain.
(a) Using the hybrid-pi model with early voltage effect, compute the small signal voltage gain, Av, input resistance and output resistance for the CE BJT amplifier shown below. Q1. Vcc = 12 V B=100 VBE(ON) = 0.7V V = 100V R = 93.7k2 * R=6 k2 Vo Rs = 0.5 k2 C B E R,= 6.3 k2 Figure Q1(a)
A transistor amplifier circuit is biased so that the quiescent point is to the far left of the load line midpoint. What do you expect to occur when the input voltage begins to vary? O The output voltage will be distorted on the bottom because it will hit the lower limit for VCE before the input voltage arrives at its peak. The output voltage will be distorted on the top because it will hit the upper limit for VCE before the input voltage arrives at its peak. O The output voTransistor's output voltage will look like the input voltage amplified and inverted. The output voltage will be zero (flat).
Please solve both
estion 2: Consider the BJT circuit given here. ( Write the input and output loop equations For the given values of Vcc= 10 V, Vin = 4V and resistor values, calculate all current values (IB, IC and IE) and VCE Assume that the ß for the transistor is 100 and the voltage drop across LED connected between Collector terminal and resistor (Rc) 2.1 V. TH i. ii. 111. VIN Vcc Rg=100 kΩ Re=2 kΩ LED 2.1 V B= 100 Based on the above analysis, correctly identify the current mode of operation Cutoff mode Active linear mode Saturation mode
a) Find the operating point current and voltage values of the non-linear element, in resistor R3 Calculate the voltage generated by the constant sources. b) Draw the circuit equivalent by linearizing the nonlinear element at the operating point. c) Using linearized equivalent small signal source j (t) to occur at R3 resistance calculate the voltage brought by it and give the expression of the VR3 voltage (constant sources and small sign sum of voltages generated by the source). E1=A=3 E2=B=8
Figure 2. illustrates a transistor amplifier implemented with a transistor (we can use PN2222 data here) and two resistors, which receives the operating voltage from a 10 V voltage source. Current gain of the npn- transistor ß=hFE = 100. Calculate a) base current IB b) collector current, Ic c) collector-emitter-voltage UCE d) determine in which state the transistor is operating (saturation, cut off, active) RB IB Rc Ic +il+ Vcc Figure 2. Npn - transistor connection. RB-300 kn, Rc-2k2, Vcc= 10 V.
In an NPN transistor used as an amplifier, which components or connections control the current flow between the others? Pick those that apply. Either N-doped regions. The base, symbolized by B controls the current between the emitter, symbolized by E, and the collector, symbolized by C. The emitter, symbolized by E controls the current between the base, symbolized by B, and the collector, symbolized by C. The P-doped depletion region.
The MOSFET based circuit shown in the figure below is used for the purpose of small signal and V are small signal input and output voltages respectively, then the circuit analysis. If V represents sig (a) Common source amplifier (c) Common drain amplifier Vsig ww RG (b) Source follower amplifier (d) Common gate amplifier
Communication Electronics