Answered: Draw the schematic diagram of a Simple…

Engineering

Mechanical Engineering

Draw the schematic diagram of a Simple Vapor Compression Cycle system as well as its P-h Diagram. Label the diagram.

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter3: Refrigeration And Refrigerants

Section: Chapter Questions

Problem 30RQ: Define a zeotropic refrigerant blend, and give an example.

See similar textbooks

Similar questions

A reheat cycle with two stages of reheating is executed, with steam expanding initially from 202.65 and 540 deg. C. The two reheater pressures are 40 bar and 10 bar, and steam leaves each reheater at 540 deg. C. Condensation occurs at 60 deg. C. Sketch the Ts - diagram. For an ideal cycle, find Qa and e. For the engine operating between the same conditions compute W and e. For a 362, 500 kg/h steam and 100 MW generator output at 94% efficiency, for actual engine, find combined thermal efficiency and combined heat rate and combined engine efficiency and quality of the actual exhaust steam. (3 decimal places in final answer pls)
Show the ts diagram and complete and step by step solution. Thermodynamics subject.
please help me with this.
Y7b please help me with the solution and answer thank you
Instructions: Perform a cycle analysis for the given reheat-regenerative Rankine cycles. Supply the table with the necessary equations based on enthalpy and mass fraction of working fluid’s state points. Derive the equations by analyzing the processes plotted in the T-s diagram. Show that the derived equations from T-s diagram analysis are consistent with the derivations by Energy Balance method. You may sketch the individual component to visualize your energy balance process.
Can you help me with this one please. Temperatures are in Kelvin unit.
QUESTION 1 An Automotive Engineering company has à task to setup a diesel engine for a new vehicle model. The engine has four-cylinder, four-stroke and 3 liters of displacement volume that operates on the ideal diesel cycle with a compression ratio of 17 as shown in Figure 1. The engine uses light diesel fuel with a heating value of 42,500 kJ/kg and an air-fuel ratio of 24. You are the engineer in the company is given the following task to analyze the engine characteristics based on constant specific heats at 500 K, a) Evaluate all the working temperatures and pressures al all points on P – V diagram. b) Evaluate the thermal efficiency of the cycle. c) If the engine is plan to operate at 3000 rpm, evaluate the power rating produce by the engine. TDC BDC Displacement Clearance volume volume Figure 1
44. The schematic diagrams of two suggested designs for a boiling water reactorare shown in the figures. One uses a direct cycle and the other a dual cycle. Theoutlet conditions for both designs are the same. In both designs, steam leaves thesteam separator assembly with a quality of 95% to enter the high pressure turbine(HPT) while the saturated liquid with 95 weight percent being recirculated to thereactor. The vapor is expanded successively in the HPT, the intermediate pressureturbine (IPT), and the low pressure turbine (LPT) before entering the condenserbeing at a 64 mm-Hg. Moisture separators between the HPT and IPT and betweenthe IPT and LPT reduce the steam moisture to 1%; the separated liquid is used toheat the feedwater in an open feedwater heater. The heated condensate and the recirculatedwater from the steam separator are pumped through the reactor. Assume100% efficiency in all pumps, and neglect pressure losses in the moistureseparators. Take all turbine efficiencies as…
ROUND UP TO 4 DECIMAL PLACES. Draw and label the P-V and T-S diagrams. 2. A diesel generator running on Ideal Air standard Diesel cycle has the following initial conditions; air at 25°C & 1 atm, having an initial volume of 0.5 m3. The compression ratio is 14 and the cut-off occurs at 8% of the stroke. The generator completes 300 cycles per minute. Determine the following: a. Pressure, volume & temperature at each state b. Cut-off ratio c. Heat Added
The heat pump produces 24,000 BTUH (where BTUH = BTU/hr) for space heating, Q_sh, plus it is heating a flow of 170 Ib/hr of liquid water from 60 F to 100 F. Freon 12 is the working fluid. a. Sketch the cycle on a Freon 12 ph chart (must be accurate and to scale and drawn onto a PDF p-h chart) b. Determine the COP for the heat pump c. Determine the EER of the heat pump
Brief the Mechanical refrigeration system highlighting the working principle, process, componentsand P-h Chart.
Draw schematic diagrams of a gas turbine system used for i. generating electricity with irreversible (actual) single stage compression, ii. two stages of irreversible expansion with reheat, and iii. a regenerator. Specify the relevant corner points of the process.