Draw the free body diagram of the system (b) Formulate the equations necessary to solve the problem (c) Determine the expressions for the acceleration, and tensions (T1 and T2) in the pulley system shown below. Assume m1 > m2. (note: the pulley is not assumed weightless and has a moment of inertia

Q: The figure represents two integral gears subjected to the tooth-contact forces shown. Replace the…

A: Given Data  The nominal radius of outer gear D0=0.2m. The nominal radius of inner gear Di=0.12m.…

Q: F=350 N C R-0.2m Vo 2 m/s Figure Q4

A:

Q: 1. The displacement formulation for a plane truss is similar to that of a mass-spring system. The…

A: The stiffness matrix of the truss is…

Q: 2- Plumb line is held steady while being carried along in a moving train. If the mass of the plumb…

A:

Q: Find the value of the spring constant k. The amplitude of the driving force is 0.505 N ar force is…

A: At resonance, frequency of oscillation becomes equal to natural frequency.

Q: Determine the reactions at the pin support and the applied moment if the bar of Figure 3 has a mass…

A:

Q: show all steps in detail, units and formulas please.

A:

Q: A block 4, of mass m is connected through a cable and a pulley to an elastic spring (see figure…

A: Given data: k=100 N/mθ=45°m=85 kg Need to determine the distance covered by the block when it stops…

Q: Three rotating masses, A= 14 kg, B =11 kg and C =21 kg are attached to a shaft with center of…

A: The inertia forces associated with the moving masses frequently generate an unbalance of forces in…

Q: The uniform L-shaped bar pivots freely at point P of the slider, which moves along the horizontal…

A:

Q: C Draw a complete and correct free-body diagram of each of the bodies designated in the statements.…

A: Assuming gravitational acceleration as g = 9.81 m/s2. Drawing FBD:

Q: Back Wheel R a Bg Front Wheel Shown above is side view of a car diving.. Front wheels are motorized…

A:

Q: The figure shows a mass-pulley system. It consists of a pulley which is connected to the inertial…

A: For the solution refer below images.

Q: Find the slack-side tension on pulley A in N.

A: Solving Part A , we assume that torque is transmitted undiminshed

Q: An industrial roller door is a uniform rectangular panel made of a heavy material, y = 45 pcf, and…

A:

Q: Generate free body diagram for the following mechanism:

A: Given data: The mass of the block hanging at point B is m. The vertical load due to the weight of…

Q: 1. Draw free-body diagrams (FBDs) for the specified rigid bodies. Then, write the coordinates of…

A: A bent pipe structure is givenTo find:(a) Draw free body diagram.(b) Write the coordinates of each…

Q: 1. In lecture I focused on a horizontal mass-spring system so we could ignore gravity, but in…

A: Given: To find: Equation for the mass Equation for y' Force when y'=0 Total energy y and y'…

Q: Find the value of the input torque on the crank-shaft mechanism in following Figure. The centers of…

A:

Q: Figure below shows two pendulums suspended from frictionless pivots and connected at their midpoints…

A: Draw the block diagram of the pendulum.

Q: The image below is of an arm in 90 degree elbow flexion holding an implement in the hand. SOLVE FOR…

A:

Q: A landing gear mechanism is shown in the accompanying figure. You may assume that it is in static…

A: Solution: Given Data: W=225 lb   To Find: (a) The force in link AB. (b) The magnitude of the pin…

Q: Q6. What is the stress concentration for normal stress due to bending at the critical location?…

A: Option - D => 1.4

Q: Figure shows a system of cylinder (m = 50 kg) and a load (m = 30 kg) connected through a rope. The…

A:

Q: The cable spool shown at the right has a weight of 50 lbs and has a moment of inertia of .28…

A: Given                  Weight, m = 50 lbs                  Tension, T = 50 lb Moment of inertia, I =…

Q: A thin uniform semicircular plate of radius R and mass m (link 1) is hinged at A and B to a clevis…

A:

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.