3/34 Calculate the magnitude of the force supported by the pin at C under the action of the 900-N load ap- plied to the bracket. Neglect friction in the slot. 45° 30 900 N 15° 75 mm 150 mm

Q: Find the minimum force F to cause movement of the 400/1000 lb. system shown. The 5º wedge is…

A: To find: The minimum force F to cause movement. Given: The 5° wedge is weightless. The coefficient…

Q: determine the number of unknowns. Calculate all reactions. Assume friction at all contact surfaces.

A: The free body diagram of each body is shown below: Here, Rh,RBv,RBH and RA are the reaction forces…

Q: A block of weight W, attached to rigid linkage AB, rests on conveyor belt moving to the left as…

A: The force diagram for the system is,

Q: 4/35 Calculate the forces in members BC, BE, and EF. Solve for each force from an equilibrium…

A:

Q: Q4: If the coefficient of static friction at B is u-0.4, determine the largest angle 0 and the…

A:

Q: Calculate the magnitude of the tension T and the angle for which the eye bolt will be under a…

A:

Q: The smooth surface of the vertical cam is defined in part by the curver (0.2 cos 0+0.3) m. (Figure…

A: Given Dataθ˙=4 rad/sr=0.2cosθ+0.3k=30N/mm=0.9kgθ=30°

Q: The rope and pulley system shown in Figure 1 has 80- and 90-lb weights attached to ropes. The 80-lb…

A:

Q: the magnitude of component parallel to the hinge axis of the door, (include units with answer) A:…

A:

Q: Determine the force P required to maintain the M-kg engine in the position shown in the figure. The…

A:

Q: Gear C drives the pulley D at a constant speed. For the indicated belt tensions, calculate the force…

A:

Q: Determine the magnitudes of all pin reactions for the frame loaded as shown. Assume F = 660 N, a =…

A: GivenF=660Na=675mmb=290mmθ=25oϕ=64o

Q: Determine reactions of hinge and roller bearing for the given Fig. 20 kN/m 15 kN/m C K 2 m ПАПТА 3 m…

A: Step 1:Step 2:

Q: The horizontal steel shaft has a mass of 590 kg and is suspended by a vertical cable from A and by a…

A: Given Data m=590 kg

Q: Balance three masses that lie in one plane as shown below, if it is known that ml = 2 Kg ; R1 = 150…

A:

Q: 5.33. The roller shown in Fig. 5-32 weighs 339 lb. What force T is necessary to start the roller…

A: The angle alpha is-

Q: Determine the magnitude of the pin force at A. Assume W = 675 lb, a = 2.7 ft, b = 2.0 ft, r = 9 in.…

A:

Q: Compute the normal force in section 1. Neglect the weights of the member. Note that point B is…

A:

Q: 4e. If the two forces are F1=(3i-2j-9k) kN and F2=(-16i) kN, Find out All the  correct equations…

A: F1=(3i-2j-9k) kN  F2=(-16i) kN As per guideline, I can solve 1 question at a time . So ,please…

Q: 4/36 Determine the force in member BE of the loaded truss.

A: Here we will use the method of section to calculate the load in member BE

Q: Determine the force P required to maintain the 235-kg engine in the position for which 0 = 34°. The…

A:

Q: Determine the forces at A and B. The force at A is The force at Bis lb 4 lb &

A: This question is based on the concept of classical mechanics on force balancing.

Q: The system above is supported by a ball-and-socket joint at point A, as well as cables BC and BD. A…

A:

Q: For the lightweight truss shown 9 kN 12 kN 9 kN C F 30° H G A 10 m 10 m 10 m 10 m ( all 30°, 60°,…

A:

Q: The Figure shown below is the truss pattern proposed by engineering students for the one part of…

A:

Q: 5-31. The mass of 700 kg is suspended from a trolley which moves along the crane rail from d=1.7 m…

A: To determine:The force along the pin connected knee struct BCThe magnitude of force at pin A=

Q: 1,2m 1,2m B A K 1,0m

A:

Q: Determine the force P required to maintain the M-kg engine in the position shown in the figure . The…

A:

Q: * Incorrect Four forces are exerted on the eyebolt as shown. If the net effect on the bolt is a…

A:

Q: determine the magnitude of the force equivalent to the forcing system shown in figure 1. Specify the…

A: Note:As per our guidelines we are supposed to answer only one question. Kindly repost other…

Q: 600 lb C 18 25 750 lb-ft B 10 900 lb| Dimensions in inches

A:

Q: Calculate the force and moment reactions at the bolted base O of the overhead traffice-signal…

A: To determine the values of reactin forces at O.

Q: k = 2 kN/m. S nocnation 45° B

A:

Q: 4/4 Caleulate the forces in members BE and BD of the loaded trum. B 1000 Ib Problem 4/4

A:

Q: he tripod below supports a vertical load P as member AB exerts a compressive force of 47 Ib. ZD =2'…

A:

Q: C7-32 A truss is loaded and supported as shown in Fig. Plot the forces in members BC, BG, and GH of…

A: Draw a free-body diagram of the truss,     Apply force equilibrium in a horizontal direction,…

Free Body Diagram

The system of forces acting on a body tends to either rotate it or make the body undergo motion. In general, when an external agent exerts a force on a body, the body undergoes translational motion and rotational motion. The body has six degrees of freedom under the influence of that force. Here, three degrees of freedom are from the translational motion while the other three are from the rotation motion. However, sometimes the bodies are not allowed to undergo any motion and are fixed, under such conditions the body is said to be constrained.