draw a connection containing 6 bolts of diameter 16mm type A325x to connect two plates each plates have the same size of 200mm width and 10mm thickness grade A36 hint : 1) use any shape of bolt's distribution to connect the two plates 2) the spacings must achieve the bolted connections requirements 3) find the shear strength of the bolts you've drawn in the previous question

draw a connection containing 6 bolts of diameter 16mm type A325x to connect two plates each plates have the same size of 200mm width and 10mm thickness grade A36 hint : 1) use any shape of bolt's distribution to connect the two plates 2) the spacings must achieve the bolted connections requirements 3) find the shear strength of the bolts you've drawn in the previous question

Architectural Drafting and Design (MindTap Course List)

7th Edition

ISBN:9781285165738

Author:Alan Jefferis, David A. Madsen, David P. Madsen

Publisher:Alan Jefferis, David A. Madsen, David P. Madsen

Chapter28: Structural Components Of Framed Construction

Section: Chapter Questions

Problem 28.34Q

See similar textbooks

Related questions

Q: Compute the capacity of the connection considering all possible modes of failure. Assume that the…

Q: The group of four bolts shown below is subjected to factored loads Pux-100 kip, Puy=75 kip. The…

A: We need to calculate shear and tension strength of bolts for bearing type connection Calculate Shear…

Q: Q21 In the connection shown in Figure below, the bolts are ¾in diameter, and A36 steel is used for…

A: The figure shown below shows the A36 steel connection with 1" bolts

Q: Determine the LRFD design tensile strength and the ASD allowable tensile strength for the…

A: Fy = 36 ksi Fu = 58 ksi 3/4 inch diameter A325 grade bolt Calculations shown in steps below

Q: Design a connection for the following conditions: • 2L 8x6xtension member • Dead load = 50 kips,…

A: Hi! Thank you for the question As per the honor code, We’ll answer the first question since the…

Q: A channel shown is attached to a 12 mm gusset plate with 9-22 mm diameter A 325 bolts as shown. Use…

A: 12 mm thick gusset plateTo determine:the capacity of the channel based on the bearing strength of…

Q: In the figure shown, the bolts are 3/4-inch in diameter, and A36 steel is used for all components.…

A: Introduction- Overall shearing capacity of a bolt is the amount of force required to split the bolts…

Q: Angle Bolted Connection. The L6 x 31/2 × 5/16. -in angles, shown in Figure, The bolts are 3/4 inch…

Q: The design shear strength phi rnv of one A490 X-bolt, 3/4 inch in diameter (Group B, X type) in…

Q: 1. A riveted lap joint is shown in the figure below. The rivets used are A502, Grade 2, hot-driven…

Q: 5. Find the allowable strength of the welded connection with a minimum throat size shown below. Base…

A: The thickness of the plate = 10 mm The yield strength of the base metal (Fy) = 275 N/mm2 The…

Q: A 3/4 in (thickness) X 5 in (height) steel plate is connected to another one through two bolts of…

Q: Questions Determine the net critical width of the bolted connection shown. Plate thickness is 25mm…

Q: 4-2. Determine the following for the connection shown in Figure 4-26, assuming the bolts are -in.…

A: Bolted Connection: A small piece of metal that consists of a head and a shank is known as a Bolt.…

Q: erify the connection in Figure below is adequate --0--0-- en: ps 100 x 65 x 8 | -6---6- Figure 6.35…

A: Data given -Angle section - 100×65×8splice plate =95×50grade of steel , fy =275N/mm2we know fu =530…

Q: Problem 6: Assume that the pieces making up the connection are adequate, and very stiff such that…

A: Service load, T=620 kNFrom the given service load, 25% is dead load and 75% is live loadGiven bolt…

Q: An A992 steel plate (12mm thick, in yellow) is connected to another A992 steel plate (12mm thick, in…

A: Given data Diameter of bolt (d) = 33mm Let's 2mm extra space is provide in hole for easy fitting…

Q: Question No.3: Determine the maximum tensile force, Pu, that can be applied to the connection shown…

A: Given:- ASTM A36 steel From AISC Manual Table 2-4, fy=36ksi fu=58ksi To find:-Pu

Q: If the nominal diameter of a bolt in a bolted connection is 7/8 in, then the minimum distance…

A: A bolt is a mechanical object that is used for fastening with the threaded shaft. They are similar…

Q: 5) Calculate P the allowable tensile load for the butt joint shown. Each A325-N high-strength bolt…

Q: The plate splice shown in the figure below has 9 – 3/4 inch diameter A325-N type bolts (Group A, N…

A: A325 N type of bolts, N indicates threaded portion will be in the shear plane. Dia of bolt = 3/4 in…

Q: In the connection shown in Figure P3.5-3, the bolts are 4-inch in diameter, and A36 steel is used…

A: Given,

Q: Determine the number of bolts required to develop the full capacity of the double angle tension…

Q: In the connection shown in the figure, the bolts are 3/4 inch in diameter, and A50 steel is used for…

A: The given data is shown below: Diameter of bolt=34-inchA50 steel

Q: etermine the net area An of a 1/4 in by 4 inches plate and the diameter of the bolt is 7/8 in.…

A: width of plate=4in thickness of plate=1/4in diameter of bolt=7/8 in to find net area of plate

Q: In the connection shown in the figure, the bolts are 3/4 inch in diameter, and A50 steel is used for…

Q: A double cover butt joint is shown in figure 2 below. If the steel is Grade S355JR and the bolts are…

A: Given, For Steel grade S355JR, fy=350 MPafu=490 MPa For bolts of 8.8 grade, fub =800 N/mm2 Assuming…

Q: A bolted connection shown is made up of 2L150 x 100 x 9.5 mm. The angle is made of A-36 steel and…

A: Draw the sectional diagram: Hole dia=25 mm

Q: A C15x40 channel section is bolted to a gusset plate is used to resist a tensile load Pu =313 k. The…

A: C15×40 channel sectionPu=313 kdia=3/4 inch A325n (group A,N type)To determine- 1) No. of bolts…

Q: Consider the following bolted connection. Slippage is pemitted. Member: L6x6x3/4 3/16 “ gusset plate…

A: Given- t=3"16

Q: Calculate the maximum tensile load, Ta or Tu of the connection shown in Figure 7. Theconnection…

A: The given data is shown below: Bolt diameter=78''A36 steelWidth pf plate=13''

Q: Example graph of a testing of Reinforcing steel bar how can you explain this?

A: The graph of testing of the Reinforcing steel bar is given 2 specimens A & B.To Find-It is…

Q: What will be the design shear strength of a bolt for the connection in which two plates, 10 mm and…

Q: The 175 x 100 x 16 mm angle shown connected to a gusset plate with three 25 mm bolts (A490) when…

A: Failure of bolt joint in tension is due to :i) Failure of bolts ii) Shear failure of the plate iii)…

Concept explainers

Bars

In civil engineering, bars refer to steel reinforcement bars or rebars. These are structural members primarily used for reinforcement purposes in masonry works. A bar is characterized by its cross-sectional area, which is negligible compared to its length. Bars are usually manufactured by steel which is uniform throughout the length, or by meshing multiple steel wires. Other materials of the bar include carbon steel, glass fiber, carbon fiber, and basalt fiber. The reinforcing bars are coated with epoxy resins and other materials to enhance some of their properties including corrosion resistance.

Question

draw a connection containing 6 bolts of diameter 16mm type A325x to connect two plates each plates have the same size of 200mm width and 10mm thickness grade A36 hint :

1) use any shape of bolt's distribution to connect the two plates

2) the spacings must achieve the bolted connections requirements

3) find the shear strength of the bolts you've drawn in the previous question

4)repeat the previous steps if the connection has 8 bolts with diameter 14mm

5) compare the results , which one is more effective

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

In the figure shown, the bolts are 3/4-inch in diameter, and A36 steel is used for all components. Considering both the tension member and the gusset plate, compute the following: Note: Limit the failure path to U-shape 3 a. Design block shear strength of the connection 2" b. Allowable block shear strength of the connection
Question No.3: Determine the maximum tensile force, Pu, that can be applied to the connection shown in figure below based on the bolt strength; assume ASTM A36 steel for the following bolt types in standard holes: Check every limit state. a. 1-in.-diameter A325N, b. 7/8-in.-diameter A490X. 3" 3" 1½" /" plate ½P, P ½P. /" plate
Based on block shear strength of the double angle.
Please I need urgent... Please give me right solution.. thank you
Determine the strength of the connection shown in Figure , based on bearing and shear, for the following bolts: a. A307 b. Group A, threads in the plane of shear c. Group A, threads not in the plane of shear
The plate splice shown in the figure below has 9 – 3/4 inch diameter A325-N type bolts (Group A, N type) on each side. Based on the shear strength of bolts only, the maximum Pu that can be applied to the splice is equal to: Group of answer choices 202 kips 322 kips 161 kips 405 kips
B1 USING NEW NSCP CODES, PLEASE ANSWER
Please answer for ASD
Part a
Consider the following bolted connection. Slippage is permitted. Member: L6x6x3/4 3/16 “ gusset plate Pu Pu A36 steel 3.5* 1"diameter A325-X bolts 1 1/4" 3 " 3* 1 1/4" Question 3.1: Please, indicate if the combined bolt shear strength is closer to: Question 3.2: Please, indicate if the combined bolt bearing strength is closer to: Question 3.3: Please, indicate if the angle yielding strength is closer to: Question 3.4: Please, indicate if the angle fracture strength is closer to: Question 3.5: Please, indicate if the angle block shear strength is closer to: Question 3.6: Please, indicate if the overall connection strength is closer to:
Calculate the maximum tensile load, Ta or Tu of the connection shown in Figure 7. Theconnection consists of two 3/8" plates fastened to each side of one 13/16" plate.Assume 7/8" diameter bolts and standard punched holes. Use A36 steel. The plate is 13” wide. Note: Be sure to check all failure modes; bolt failure modes, and member failure modes(including block shear)
5) Calculate P the allowable tensile load for the butt joint shown. Each A325-N high-strength bolt has a diameter of 0.9 inches. The plates are made of ASTM A36 steel. If the applied load is 200 kips, is this connection adequate? If not, what needs to be changed so that this connection can handle an applied load of 200 kips? P- ФФ P ! 12"x " P. P.