Please make your own question about vertical distance (surverying) and solve it on your own. Make it original. Do not send the same answers if you see this question again, make another one. Thank you. I'll upvote.

Q: A wood beam carries the loading shown in the figure. calculate the magnitude of the bending stress…

A:

Q: On a map of scale 1:75,000 the map distance measured between points A and B is 5.0 cm. If a sketch…

A: Find scale for sketch of same area

Q: The center of gravity of the 50-kg spool is at G. A cable wound around the hub of the spool is…

A:

Q: Design of steel-structure- A steel rod of 12 mm diameter is used as a tie in bracing system. It is…

A: Given data- A steel rod- Diameter D=12 mm, Steel rod is used as a tie in bracing system. Rod is…

Q: The long chord from the P.C to the P.T of a compound curve is 270.94 meters long and the angles its…

A:

Q: Determine the design capacity of the given tension member. Assume that the slenderness requirement…

A: Answer We are given L 7 x 7 x 1 (Ag = 13 in2 , x=2.115 in) ASTM A36 (fy = 40 ksi , fu = 60 ksi) Bolt…

Q: S = 1 : 18,000; f = 152.40 mm Express your answer in feet to three significant figures. H = Submit…

A:

Q: Determine the factor of safety, F, for the infinite slope shown in Figure 15.48, where seepage is…

A: The slope is the ground with an inclined surface or the ground connecting two varying elevations.…

Q: Determine the shear force 5.18 ft to the right of point A for the beam shown belowif P = 867 lb, W =…

A:

Q: This is incorrect, please redo it, I have attached what the correct answers are supposed to be S

A: For a given soil profile, there is an upward seepage occurring. The velocity of the upward flow, v =…

Q: A truss frame is shown below, using Virtual Work Method determine; Use: E = 200 000 MPa, A = 150 mm?…

A:

Q: A simply supported beam with overhang on the right support is shown below. Using virtual work…

A:

Q: Please make your own question about horizontal distance (surverying) and solve it on your own. Make…

A:

Q: What are the errors faced in electronic distance measurement?

A: Electronic distance measurement  is a device which measure the distance  with help of infrared,…

Q: ANSWER

A:

Q: a. Station of PCC b. Total length of the compound curve (LCC) c. Station of PT

A: Given: The azimuths of the first, middle and last tangent is given as: θ1=172°θ2=190°θ3=202° The…

Q: A beam is subjected to equal 19.6 kip-ft bending moments. Assume t1 = t2= tw= 1 in., d = 13 in., b1…

A:

Q: Write AutoCAD commands for drawing the following figure (without color). Use Relative Polar…

A:

Q: Determine the required diameter (in inches) of rod ACif the allowable normal stress is 22.51 ksi and…

A:

Q: Determine the largest weight W (in Ib) that can be supported safely by the structure shown in the…

A:

Q: A bucket is hanging from a horizontally moving crane. Calculate the maximum allowable speed (m/s) of…

A:

Q: Determine the forces in members BC, BE, and BF. The triangles are isosceles. The forces are positive…

A: Solving question AFig is Giventhere is horizontal line symmetry for the handlesno line of symmetry…

Q: Problem 2. Given the following traverse notes for a closed traverse, LINES AB BC CA AZIMUTH 225°…

A:

Q: A 3-m 150 mm CHB wall rests on a 600 mm thick concrete footing. The CHB wall weighs 3.3 kN/m² and…

A: The length of the wall = 3 m Footing thickness= 600 mmThe weight of the wall = 3.3 kN/m2 The live…

Q: 2. Slope and deflection at the free end. 20 kN/m -3 m 50 kN 2 m 40 kN 100 kN-m

A:

Q: What are the geocentric coordinates in meters of a station which has a latitude of 48°22′37.79300"…

A:

Q: 3. (a) Slope at A and B; (b) deflection at F, C and E. F 4 kN/m im A 6 kN/m 1 m- |C -1 m 4 kN/m 10

A:

Q: Solve the area of the lot from the given data shown by triangle method. Course Observed Data…

A: Course Lattitude Departure Double meridian Distance Double Area (DA) AB -497.28 -56.66 -56.66…

Q: solve question 7 please sir

A:

Q: Item 6 The angles of a five-sided traverse are turned so that the 95% error of any angle is +3.4"…

A:

Q: 5. In a constant-head permeability test, the length of the specimen is 200 mm and the cross…

A: Given data : Coefficient of permeability (K)=2.1×10-2  cm/secRate of flow (q)=130 cm3/minLength of…

Q: _feedback is used by Schmitt trigger

A: Schmitt trigger is a comparator circuit with hysteresis.  A Schmitt trigger is a logic input type…

Q: Draw the shear and moment diagram of the loaded beam shown below and determine the maximum moment…

A:

Q: A tied column which is subjected to an eccentric load has dimensions of 300 mm x 500 mm which is…

A: Answer  (a) Calculation of value of the Nominal load 'Pn' Let us first draw the free body diagram…

Q: 8. Design the angle purlin for the following specifications Span of truss =9m c/c, Pitch 1/5 of…

A: (8) Answer Calculate critical load  critical load is considered as maximum of below 2 factored…

Q: PROBLEM The rigid bar ABC is supported by a pin at B, vertical steel rod at A and vertical bronze…

A: Given data in question  Area  Length Steel and bronze rods Modulus of elasticity  Permissible…

Traverse Survey

Traverse surveying is a popular method of surveying. Traversing is that type of survey where several connected survey lines form a framework and the directions and lengths of the survey lines are measured with the help of a tool to measure angles and tape or chain respectively. Traverse networks involve placing survey stations in a queue or trail and using pre-tested points as a basis for looking at the next point. This type of surveying is different from Tacheometric surveying, where only angles are measured and the process of chaining is reduced.