Draw the shear and moment diagram of the loaded beam shown below and determine the maximum moment (kN-m) and maximum shear (kN). 15 kN/m 5m 2m Next >

Q: Sketch thefollowing figure ,orthographic view ( using catia )  Metion the top view side view and…

A: From figure.......

Q: The six standard views in orthographic projection are front, top, bottom, and what?

A: Answer : Left view Right view  Rear view

Q: D. SKETCH: (Draw the resulting figure based on the data given on a graphing paper. Vertical axis or…

A: Station BS HI FS IFS Elevation (m) BM -1 1.515 101.515     100 0+000       1.520 99.995…

Q: The following is the bearing and length measurements of an opentraverse A) Determine the latitude…

A: The latitude of the traverse line is extend on the north and south direction and departure of the…

Q: Determine the X coordinates of the centroid of the trapezoidal area shown.

A: Given data : The given figure in divided into Rectangle and Triangle Rectangle: Width (B)=120 mm…

Q: In the exhibit below, What is the distance from A to C, A O 1078.57' O 1087.75' O 1187.57' O…

A: Given values: Consider closed traverse given. For closed traverse, sum of latitude and sum of…

Q: How stadia interval factor is determined?

A: The Stadia interval: The Stadia interval is defined as the ratio between the focal distance between…

Q: Example: reading around a 10x10 cm square area = 0.995 rev Reading around the required area = 5.765…

A: 10 cm square =0.995 rev 1 cm square=0.00995 rev area of required area=5.765 rev required area in cm…

Q: Calculate the y-coordinate of the centroid of the shaded area. The triangle is equilateral.…

A:

Q: 0+365 0+370 0+375 0+380 BM2 1.008 0.953 0.880 0.800 0.783 COMPUTATIONS: 1. Computing Height of…

A: The formulas to be used are given in question

Q: Show Isometric View.

A: Answer  We can obtain the isometric view from given views in Autocad using the following steps 1)…

Q: Area of the Triangles are denoted by the following formulas: 1. Basic Formula, A = 12 * base*…

A: Given: From the figure, AC=1690.54 m

Q: 15.16 Refer to Figure 15.52. Using Michalowski's solution given in Figure 15.25 ('> 0). determine…

A: The kinematic approach of limit analysis is applied to the rigid rotational collapse mechanism by…

Q: Draw the Orthographic Projections (Top View, Front View, Side View) For the Shapes Shown Below,…

A:

Q: 02. Draw a neat sketch (closed traverse) for this note book entry. D 55 40 C24 24 30E B22 10 A

A: Given:- The notebook entry is given  To determine:- Draw a neat sketch for the closed traverse

Q: 5 TOP 10 8 FRONT ? Isometric View RSV

A:

Q: hat are the uses of hydrographs?

A: A hydrograph may be used to show how the  water flow in a drainage basin particularly river runoff…

Q: Find the areal scale for the following 3cm+09km

A: Given: Map distancex=3 cm Ground distanceX=9 km To find: Areal scale

Q: Draw front and top view in Ist angle projection 016 R20 14 44 24 1. 40 30

A: >>>Given that the figure is ISOMETRIC diagram and we have to draw it in a 1st angle…

Q: Draw the the 3 principal views and auxiliary view (like in the second photo)

A: Auxillary view: The orthographic view drawn taken according to the line of sight which is not…

Q: 60 mm 30 mm 30 mm 45 mm

A:

Q: the centroid location formulas on step 2 come

A:

Q: earson MyLab and Mastering X roblem 9.19…

A:

Q: Q2: Draw front and side view projection for the following 36 12, 34

A: Given section: If you look at the given section from the front, the red coloured area will be…

Q: B Look to the Contour map above Solid line is the ground surface level Dashed line is Water table…

A: Contour lines are drawn on contour maps which represents the elevation or depression at any…

Q: Explain oblique angle of projection

A: oblique angle of projection- it is a graphical projection with parallel line which is used to…

Q: By using the figure below, reproduce this by using the relative rectangular coordinate entry. You…

A: Required To reproduce the given figure in question and to give the commands used to draw in AutoCAD.…

Q: g1= Station 18+26 18+00 17+00 16+00 15+68 g2= X 0 Elevation of BVC = gix 82-81x2 2L Elevation 899.02

A: Vertical Curve : Vertical curves, which may or may not be symmetrical, are supplied to alter the…

Q: 5/49 Determine the x- and y-coordinates of the centroid of the shaded area. -50 y I -150- 100…

A: The below figure is given,

Q: 20 20 FRONT ELEVATION 60 20 60

A: For given isometric view following are top, front and side views are first angle projection views

Q: In the exhibit below, What is the distance from A to C, A O 1078.57¹ O 1087.75' O 1187.57' O…

A: To Determine Distance from A to C, L = ?

Q: 1 / 2 \text { inch } \times 1 / 4

A: To find:- 1/2*1/4

Q: What are point positioning equations?

A: Point positioning are used for positioning with GPS. In point positioning, a GPS receiver which…

Q: Determine which commands can be used for this drawing. (AUTOCAD COMPLETE VERSION) Select all that…

A:

Q: Explain 1st and 3rd angle of projection

A: First angle projection and Third angle projection are two different methods of creating a 2D drawing…

Q: give me answer for 700 m radius?

A: Design speed (V) = 80 kmph Superelevation provided (e) = 7% or 0.07Radius (R) = 700 m

Q: Determine coordinates of centroid of the following shaded area.

A: Hi! Thank you for the question, As per the honor code, We’ll answer the first question since the…

Q: A line CD starting at any point, C, is 8 m long bears N 35° W, and slopes downward from C to D at…

A:

Site Plan Requirements

A site plan (also known as a plot plan) is a diagram or process to show the proposed improvements on an existing property. A site plan is important, as it provides information regarding the landscape features of a given plot of land.  Zoning is done or can be understood with the help of a site plan.