Differentiate structural design and structural analysis on your own words.

Q: Wide flange shapes, (W-shapes), are considered economical members because: O the majority of the…

A: A wide flange shape, also known as W-shape, is a structural steel member which is commonly used in…

Q: The state of stress at a point is the result of two loadings as shown in figure. When acting alone,…

A: For the two loadings act simultaneouslythen resultant (absolute) shear stress at that point with…

Q: A thin rectangular plate ABCD has a weight of P=200N, and its sides AB=60cm, AD=80cm. If the plate…

A:

Q: A,f, 107.4 mm 0.85/,'b Ca/B =107.4 mm / 0.85

A: Given data,

Q: Find the ultimate moment of resistance for the rectangular section reinforced as shown below.

A: b = 280 mm              d = 510 mm              d' = 50 mm (Taking 50 mm effective…

Q: Referring to the following illustration, a -4% grade meets a +5% grade at the point of vertical…

A:

Q: Answer the attached question.

A: by this question  first calculate particulate cut size  we know the formula for cut size…

Q: Please explain Part B properly. any classification table is there? How is the order and level…

A: Given: Misclosure= 15mm Total length,K= 10 Km Required: Order of levelling

Q: can you send me a written solution?

A: Given, Specific weight of sea water(w)=64 lbft3w=64 lbft3 Length of gate(L)=6 ftL=6 ft Width of…

Q: Determine the reaction/s at each support, given the data and figure below. X 3 kN/m Y= 14 kN/m L= 3…

A:

Q: many biological random variables that can be modeled by the normal distribution. Assume the heights…

A: let consider μ=mean of height =69               σ= standard deviation=3.5

Q: Answer the attached question.

A: Given:- speed = 10000acfmT=200 oF1 atmParticle density = 1200kg/m3To find:-Lappe conventional…

Q: 2. The second floor of a light manufacturing building is constructed from a 125-mm-thick stone…

A: Thickness of concrete slab(tslab) = 125 mm = 0.125 mThickness of cinder concrete (tcinder) = 100 mm…

Q: Determine the yield modulus of elasticity and yield strength of an aluminum material with the…

A: The stress is taken in y-axis and strain in x-axis. From the data, stress-strain curve are being…

Q: Thank you for your answer but I can't see the right side of the page, see image below what i see

A: HMA = 210 mm Base = 300 mm Sub-base = 500 mm Reliability = 95% ∆PSI = 1.75 S0 = 0.45 TSI = 2.5 Cd =…

Q: Example 12.4 Given: A 1/20 scale model of a high-rise building is tested in a wind tunnel. The drag…

A:

Q: SURVEY ENGINEERING A survey monument is installed at STA 12+55.25'. The monument needs to be moved…

A: Given: Current Station = STA 12+55.25’ Increase in station = 177 in

Q: Find the atmospheric pressure when the barometer reading is 800 mmHg. Given the specify gravity of…

A:

Q: - 3f+ + ft tift Sowe rractons and s how shear and moment equa fons @ each section of the bean

A:

Q: An experiment on an ideal gas was conducted at a temperature of 170 degrees Fahrenheit [F] and a…

A:

Q: Answer the attached question.

A: Using the following equation:

Q: ) Determine the support reactions and 1) Sketch the axial load, shear force and bending moment…

A:

Q: Answer the attached question.

A: Given:- flow=120 m3/min overall efficiency = 70 % gas density = 1.0kg/m3 gas viscosity=0.07 kg/m-hr…

Q: Hello! Would it be possible to included a step by step solution without skipping something and add…

A:

Q: How would you interpret the results of proctor test? Use sketches, where necessary, to illustrate…

A:

Q: I want the answer to be detailed with referenc

A: A contract is an agreement that specifies the rules and regulations that must be followed by two or…

Q: Locate the centroid i and ỹ of the shaded area shown.

A:

Q: The T-section shown is subjected to a design ultimate moment of M = 180kN.m. Find the require area…

A: Solution: Given: fc = 30 MPa fy = 450 MPa bf = 400 mm hf = 100 mm bw = 200 mm d = 350 mm

Q: The given BEAM carry: - a uniform LL of 6.5 kN/m - concentrated LL of 15 kN - 4 kN/m DL Solve for…

A:

Q: Give at least 5 examples of design challenges

A: 5 examples of Design Challenges1. Frequently Change in DesignThe engineer have to change the design…

Q: 3. A pump is used to transport water at the rate of 0.075 m³/s from a reservoir 20 m above the pump…

A: Given data:- The given discharge,  Q=0.075 m3/s The given value of D is, 15 cm=0.15 m The value of…

Q: ALL 15/ A square lead slab of side 50 cm and thickness 10 cm is subjected to a shearing force (on…

A: Calculating the area of the face on which force is applied: A = 50*100    = 500 cm2   = 500*10-4 m2

Q: Answer the attached question.

A: Given: The pressure drop through the filter for a function of time, t is given by…

Q: Find the Shear and Moment at the sections where marked for the beam shown. S? M? 3 m 15 kN S?IS?…

A: Given Load 15 knSpan 9 mTo find out SFD & BMD values at A , B and C

Q: terms of x, and then draw the shear and moment d for the beam.

A:

Introduction to Architectural Drafting

Architectural drafting converts vision and ideas into technical drawings and detailed plans for the construction of buildings, such as institutional, residential, and commercial buildings. It helps engineers and architects to outline the working data and details, such as structure type, codes, elements, and kind of materials.