Find the scale for each drawing/model: 1. Drawing length: 9 in. Actual length: 45 ft. 2. Model length: 6 2/5 m Actual length: 120 km

Q: Which of the following shapes are generally considered when the area is ?computed by map…

A:

Q: put dimensions on the drawing using the details

A: 3@50, 5@100, 7@150, and rest at 200mm center to center is spacing of ties in column. This detail…

Q: What is the overall density? %

A: This question is related to the Soil Mechanics from Civil Engineering.

Q: Add/Subtract the following DMS measurements by hand. In your answer, separate each unit by a comma…

A:

Q: How many "varas" are there in a single ruler measurement?

A: A single ruler is the standard ruler which has measurements given in inches or mm. It is used to…

Q: Law of Cosines (Engineering):

A: Law of cosines signifies the relation between the lengths of sides of a triangle with respect to the…

Q: A triangle has an area of 14 sq ft and a base of 7 feet. What is the height of thetriangle?

A: given data :  area of triangle (A) = 14 square feet  base (b) = 7 feet  height (h) = ?

Q: What scale is used if a line 84 mm long represents a fence 63 m long?

A:

Q: List the four distinct kinds of drawings according to their projection methodologies.

A:

Q: - What are illustrative drawings? 2.- What is the most widely used type of illustrative drawing in…

A:

Q: what if you were given a cross-sectional area ratio of 5:1

A: If cross sectional area ratio is 5 : 1, then if the fall in the left tube be x, therefore the rise…

Q: continue dimension and baseline dimension?

A:

Q: Only Draw profile with appropriate scale

A: To draw the profile to the given levelling

Q: derivation of the formulas used in every section

A: This question has been taken from fluid mechanics

Q: Generate isometric drawing from multiviews using drawing tools or free - hand. Use approximate…

A:

Q: Please solve it within 20-25 mins A plan 6.5 x 6.5 cm represents an area of 152100 sq.m. construct…

A:

Q: Draw the three projections showing the measurements, thanks for the cooperation

A:

Q: 10 divisions of vernier scale are equal to 11 divisions of a main scale of each 0.1 mm. What is the…

A: Given data- 10 divisions of vernier scale=11 divisions of main scalemain scale one division=0.1 mmTo…

Q: Quest- A column cross-section 300 mm*400 mm, 2250 mm long fixed at one end free at another end. What…

A: Effective length of the column with one end fixed and the other end free = 2*unsupported length.=…

Q: How is unit weight expressed in primary dimensions?

A: Unit Weight is defined as the Weight of soil per unit volume.

Q: List the steps in details to draw the shape below using AutoCAD commands 330 450 330 0360 Ø200 440…

A: Solution: 1. First we need to set the units, by typing 'UN' in command box on Autocad. As units are…

Q: Q5A)The figure below represent a grid for a parcel with (25 m x 25 m) sub-grid dimension Draw the…

A: using interpolation

Q: In which sectors and where are tubular cross-section shapes used? Why is it used?

A: Tubular sections or hollow sections are used as column sections Column sections not only receive…

Q: Which of the following shapes are generally considered when the area is ?computed by map…

A: Given: shape of map To determine:  Which shape generally considered  for area calculation.

Q: With the aid of an illustration, describe two methods by which areas bounded by irregular lines can…

A: Areas bounded  by irregular lines can be found by using midoridnate rule , trapezoidal method ,…

Q: If the actual dimension is 46 m and the scaled dimension is 184 cm, what is the scale used?

A:

Q: ooking at the X direction, provide the front view, top view, and left-side view using the meter…

A: The isometric Front, and side. Top view of above drawing is given below:

Q: Determine the shape factor

A: Given:- An I- section is given  To determine:-  The shape factor of the given section

Q: 1.00- $.25 1.00 1.50 50 50-te 25 .75 D.50 1.00 1.00 1.00 50 25 -,75- 1.00 1.00 3.00 -- 200

A:

Q: Do not include the unit in writing the answer. Use small letters (lowercase) in writing Complete the…

A:

Q: If you obtained a drawing that contained Auto CAD polylines representing contours, what is the best…

A: Contour lines : A contour line for a two-variable function is a curve that connects locations of…

Q: What is the actual area enclosed by the following figure, using the scale of 1"=40'? 4" Area = _ft²…

A: Converting given dimensions to actual dimensions on field

Q: Draw the shear, bending moment, and axial force diagrams and the qualitative deflected shape for the…

A: Solution: Draw the free body diagram of the frame :

Q: Describe the purpose of virtual mock-ups, 4D and 5D building information models in construction

A: From the given question it is required to describe the purpose of virtual mock-ups, 4D and 5D…

Q: 9. Which among the following is a standard scale for a similitude?

A: In fluid mechanics, we use similarity as a similitude  This means two shapes have the geometrical or…

Q: Part A What is the ratio scale for the equivalent scale of 1 in. = 80 ft? Express your answer using…

A: 1 ft =12 inch given 80 ft =12*80=960in Ratio scale=112×80=1:960

Q: Calculate the perimeter and the area of the triangles with the following dimensions (refer to Figure…

A: Given data- a = 10'0" a = 2750 mmb = 9'6" b = 2050 mmc = 3'0" c = 300 mmh = 2'0" h = 600 mm

Q: 25) In 1950, plan of a rectangular field was drawn with a scale of 1 cm = 40 m. The present…

A:

Q: Convert 0.0351 to engineering notation. O a) 35.1 × 103 O b) 3.51 × 10–2 )c) 3.51 x 10² O d) 35.1 ×…

A: Solution:- We have to convert the given number into the engineering notation, The given number is…

Q: Draw the figure to an enlarged scale in Isohyetal method

A: The iisohyetal approach is a technique for calculating the average amount of precipitation within a…

Q: What is similar flexure and contrary flexure and also draw a sketch what is the formula for…

A: Introduction- To assist in the transfer of railway and roadways vehicles from one track to another,…