Develop an assembly code for an LED 8-bit binary counter, where LEDs are connected to the Port 2. Here are the instructions, (1) counter should start when a HIGH input is present at P1.0 and stop the counter when a LOW input is present/read at the P1.2. (2) Draw the circuits diagram. Hint: Switch connected to P1.0 should pass HIGH when switch is pressed, where as switch connected to P1.2 should pass LOW when switch is pressed. Accordingly adjust your circuit connections and the code.

Q: 3.(a) Make a truth table for this given logic gate, as shown in the figure. Show the steps. What is…

A: “Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: Implement Four-to-one-line multiplexer with Logic diagram and Function table.

A:

Q: Design a three input NOR layout so that rise time and fall time become equal when input logic…

A: Given: A three-input NOR layout so that rise time and fall time become equal when input logic…

Q: Draw the logic diagram and transistor implementation for a (2-2-2) AOI.

A: The logic diagram can be implemented as,

Q: Q2) B) Use the SAR ADC to convert the analog voltage of (7.28 V) to 8-bit binary. If (VREF = 10V),…

A: Conversion table is given by, Thus the final binary output from D0 to D7 will be, 010111012

Q: What is interface. What is program block and module block.

A: To verify a design we write verification module and  test bench to check that it meet specification.…

Q: Use the following figure to answer the following question: In this circuit (inverter), the…

A: When the firing angle of the rectifier is less than 30o, the expression for the output voltage for…

Q: Show the schematic of a LUT (using a multiplexer0 which implements the logic for a 3-input AND gate.

A:

Q: Option 4: 50,250,350,550

A:

Q: Explain the function of Multiplexer and, Draw the 2 x 1 multiplexer logic circuit diagram and…

A:

Q: Part 1: The NAND Gate latch (1) Create the circuit of NAND Gate latch (as shown in Figure 1) on a…

A: The latch is a  device that stores 1 bit of data and it is a level triggered device.

Q: The no. of turns in secondary winding is more than that of primary winding. The output voltage is…

A: The no. of turns in secondary winding is more than that of primary winding. The output voltage is…

Q: Compare the behavior of the 7408 2-input AND gate with that of the 7400 2-input NAND gate. In what…

A: The 7408 is a 2-input AND gate, while the 7400 is a 2-input NAND gate. Here's how they behave…

Q: Define the analog and logic circuits. List the Logic Circuit advantages / disadvantages.

A: An analog circuit is a circuit which gives a continuous signal (continuous in both time and…

Q: 3. What is analogue to digital conversion & explain in detail 2-bit quantization.

A:

Q: i. Draw the circuit diagram of 4-bit Ripple Carry Adder.

A: To draw the circuit diagram of 4 bit ripple carry adder 4 full adders are connected one after…

Q: For the basic TTL gate shown in figure (5), if logic (1), BR = 0.02 and Br = 100, then find the v…

A:

Q: Suppose an analog-digital converter IC ('chip") inputs a voltage ranging from 0 to 3.5 volts DC and…

A: We need to find out the number of steps and step size for given analog to digital converter.

Q: Output voltage of an inverter is controlled by multiple pulse modulation technique. If the peak…

A: Given- Peak value of reference voltage Vr = 4 V, Peak value of carrier voltage Vc = 6 V, To Find-…

Q: 3. Output voltages according to the input voltages of the logic gate given in Figure 1 are given in…

A:

Q: Draw a logic diagram of a divide-by-14 counter using IC 7493 and 2-input AND gate.

A:

Q: What is a TTL circuit? What are their main characteristics? (Input voltage and current, output…

A: TTL Circuit It is abbreviated as Transistor-Transistor Logic. It comes under the category of the…

Q: 4) Design and draw these memory units with their control circuits. Explain operations. a) A single…

A: As per the rules we can answer only one question, please post the remaining questions as the…

Q: Draw a switch-level model for a CMOS NOR gate in the style of Figure 1-14, showing the same three…

A: Step 1: The standard CMOS NOR gate can be drawn as follows: Step 2: For both inputs LOW: Step 3: For…

Q: Q4. Open collector logic gate is shown in Figure. What logic function is performed by this circuit?…

A: the answer is,

Q: a) When does an E-MOSFET act as an open switch? b) When does an E-MOSFET act as a closed switch? c)…

A: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question and…

Q: For the circuits shown in figures 1 and 2:- What is the function of output? 2. Find the max. and…

A:

Q: show the classification of semiconductor memories.

A: Please refer the attached images for the complete answer..

Q: 4) Write the function table for the given 1-bit ALU in the figure. b Ainvert LO Binvert B invert…

A: Given Data:One-bit ALU functional diagram with,The control signals…

Q: are connect

A: The inverter is a logic gate which invert the input to the output. When the input 0 is given to the…

Q: Fill-in the blank boxes with the correct LOGIC GATE/ Full/Half Adder

A: The given circuit is a 4-bit subtractor, whenever we perform subtraction, the subtrahend should be…

Q: (b) The logic gate from (a) needs to drive a capacitive load of 150 ff with a rise- time and…

A:

Q: a) When does an E-MOSFET act as an open switch? b) When does an E-MOSFET act as a closed switch? c)…

A: “Since you have posted a question with multiple sub-parts, we will solve first three subparts for…

Code Conversion

The method or technique used to convert code from one format to another is termed code conversion. Code conversions are most commonly used in computers, digital electronics, microprocessors, etc.