Determine the y-coordinate of the centroid of the shaded area.

Q: 4. Replace the coplanar force system that acts on the casting with an equivalent force-couple…

A: 4) From the triangle, sinθ=35cosθ=45

Q: Pin: MMC LMC Geom. Tol. с 1.000 1 1.000 Ø.515-.540 Hole 0.010M ABC 1.000 B Figure for Problem 21…

A:

Q: Required information A 24-mm-diameter uniform steel shaft is 600 mm long between bearings. Take the…

A: the diameter of the steel rod d = 24 mm = 0.024 mthe length of the steel rod l = 600 mm = 0.6 mthe…

Q: WHAT 16 THE NOMINAL RATE OF INTE REST COMPOUNDED CONTINOUSLY FOR IOYRS IF THE COMPOUND AMOUNT FACTOR…

A: Answer: The nominal rate of interest is 3.0455%.

Q: RPM meter of the car is an example for control of process application of measurement system. Select…

A: A tachometer or RPM meter is an instrument measuring the rotation speed of a shaft or disk, as in a…

Q: Use Bayes’ Rule to solve the following problem: The new engine subcomponent was tested in two…

A:

Q: following statements, answer True or False and explain the answer briefly. The tolerance of…

A: Yes, it's true. The tolerance of standard mass used must be smaller than the uncertainty of…

Q: A reversible refrigeration cycle operates between cold and hot reservoirs at temperatures Te and TH,…

A:

Q: Complete the following sentence strain gauge has input as displacement and output as……

A: GIVEN-  displacement is the input of strain gauge to be find- outout of strain gauge

Q: QI) A) Fill the following blanks 1- Misalignment of measuring instrument is called 2- Applying a…

A: 1. Misalignment of measuring instrument is called Abbe's Error 2. Applying a number of known…

Q: 6. Determine the correct statement Mark only one oval. O It is preferable to have a temperature…

A: 1st statement is correct only.

Q: View Policies Current Attempt in Progress Calculate the moment Mg of the 945-N force about the bolt…

A:

Q: 2 600 STOP SIDE SECT OF TIMEL 12 €7790100-17 2E00073 13121425675 2272-5003 112 991 10130780053-933…

A: The number of pieces in the given figure

Q: You are given a set slip gauge containing 46 pieces of 2mm base (M46/2). Show how you would build…

A:

Q: 03 A: For the measuring instrument of Watt Flyball Governor shown in Figure 5, answer the following…

A: Specific Schematic Diagram of Functional Elements (Watt Flyball Governor): The Watt Flyball Governor…

Q: Metrology Discuss both figures and explain which one comply with Taylor principle and why?

A: Taylor's principle in metrology says that the GO gauge should check all the dimensions of the…

Q: 3. If the tolerance applies at MMC then a possible O indeterminant bonus O LMC zero tolerance…

A: given = fill in the blanks

Q: Please help me with number 7,8,11 and 16. This is not graded

A: Solution    7. PITCH-This is the distance from a point on the screw thread to a corresponding point…

Q: The car weighs 1650 lbs and drives up the hill at a constant speed. Assuming the static friction…

A:

Q: For the truss loaded as shown, determine the equation for the line of action of the stand-alone…

A:

Q: GER SCALE 9 v 1.3- A 3"-2 ACME .75 1.5 "5 SECTION A-A Ø3.75- D-50 Top and front views of the…

A: Adjusting screw is a screw with threads from 40 to 100 threads per inch. Typically stainless steel…

Q: gative loop of the indicator diagram Spring cons,

A:

Q: a) A turbine connected to an electric generator through a gearbox can be modelled as illustrated in…

A: “Since you have posted a question with multiple sub parts, we will provide the solution only to the…

Q: An experimental device imparts a force of magnitude F-34 lb to the front edge of the rim at A to…

A:

Q: Calculate the moment of inertia of the shaded area about the x-axis.

A:

Q: c) Calculate the new stress ratio R, the stress amplitude o, in MPa and the mean stress o in MPa.…

A: In this problem, it is asking the answers for parts (c) and (d). (c) Write the given data. σmin=-132…

Q: Calculation of Limits using ANSI B4.1 Standard Tables, when one of the design Features Exists. When…

A: Given:The nominal shaft diameter is .For Interface (force fit):The upper limit of the shaft diameter…

Q: Determine the coordinates of the mass center of the body which is constructed of three pieces of…

A: Given question: Determine the coordinates of the mass center of the body which is constructed of…

Q: How much work is done by a force applied to a spring of stiffness k that increases the extension of…

A:

Q: A schenatic of a clutch-testing achine is showE The steel shaft rotates at a coestat speed a As…

A:

Q: Determine the Grashof condition and Barker Classification for the following mechanism: 8" 3.25" X…

A: S= 3.25"L= 9.38"P= 6.75"Q= 4.32"

Q: In calibration of instrument the 0.055 percent of the calibration span what does it mean. If let say…

A: The calibration span is the total range of the instrument's observing range, which means the…

Q: is a measure of sensitivity of a strain gauge and is represented as the ratio of to A. BSF,…

A: Strain gauges are the devices which are used to measure the stresses in equipments or parts.

Q: 1. Determine the value of M1 if the system shown is equivalent to a single force acting at point C.…

A: Given dataX=1Y=6Z=0M2=3000kips

Q: Match thể Items Column I P Addendum

A: Given: Match the following,

Conservation of Energy

In physics, the rule of the conservation of energy states that energy doesn’t disappear from the atmosphere; instead, it changes its form from one type to another. Energy is one of the most important physical quantities in nature, and it cannot be created or destroyed — only transformed.