dicate the number of pieces in Image 1.

Q: Statics Question The diagram shows 2 vectors. Solve for the resultant vector (force and…

A:

Q: can you do it in polygon

A: Given vectors : A :  2 kph 45°N of E B :  2.8  kph 58°E of S C :  5.1  kph 28°W of S D : 3.2  kph…

Q: 38 17 Hole Tam delik 18 19 20 20 8 26, 20. 89

A: Given:-

Q: rection: Locate the center of gravity in figures A & B by putting a dot or a point in each of the…

A: centre of garvity is the point where the gravitational force is acting through

Q: (degree) Calculate the measure of the angle in degrees marked in white for the following figure 24…

A:

Q: (Compute) What is line OA's direction cosine angle, in degrees, from the y-axis (θy)? Note that…

A: The cosine angle between two vectors  is as followes,

Q: Given the multiview projection of the solid, draw the isometric view.

A: Given:To find:Draw the isometric view.

Q: Q2: Select physical dimensions and produce engineering parts list You are to select two deep groove…

A: The Answer is below

Q: 30r 20dls 20 10r 20 20 30 150 100

A:

Q: Draw the isometric and orthographic sketch of the given figure (in catia V5 ;no hand drawing );

A: isometric view

Q: Given the isometric drawing of the solid, draw the multiview projection. L HRP FRP L FRP PRP L

A: Given the isometric drawing of the solid, draw the multiview projection.

Q: Shown in the image is a vertical section of a 66 block grid of a gold mine deposit. Each block is…

A: Based on the image presented, which includes varying ore grades ranging from 1.4 g/t to 2.9 g/t in…

Q: O v2 1

A: Given Data : Unit vector

Q: Q5 The sheet metal form as shown in Figure Q5 and has a dimension with x, y and z axis respectively.…

A:

Q: for this question just sketch what it should look like:

A: Note : Window is denoted by point P

Q: The figure below has the following weight per length. W₁ = 150 lb/ft W₂ = 175 lb/ft W3 = 130 lb/ft…

A: given;   w1=150lb/ftw2=175lb/ftw3=130lb/ftAB=1ftBC=6ftCD=4ftDE=5ftEF=8ftlets take reaction force at…

Q: Question 5 The force F in Figure A is to be replaced by a force through A and a couple whose forces…

A:

Q: 1.3 Please help. Written on paper not typed on computer or keyboard please. Need help both…

A: Sure, based on the information provided in the text accompanying the image, the angle between lines…

Q: 3. The distance between end projectors of a line CD which is inclined 45° to VP, is 60 mm. Point C…

A: the distance between end projector of a line CD which is inclined 45 to VP , is 60mm . point C is…

Q: Draw the orthographic Projections of given object.

A: Required orthographic views of the given isometric view are drawn on grid paper. 1 Grid = 1 Unit

Q: Given the multiview projection of the solid, draw the isometric view. HRP FRP F DA FRP PRP

A: Given the multiview projection of the solid, draw the isometric view.

Q: Sketch a isometric drawing for each of the three sets of orthographic drawings

A: Given: A set of orthographic projections.

Q: 2.3 Please help. Written on paper not typed on computer or keyboard please. Need help both…

A: ## Determining the Net Torque on the Wheel (Considering the Image)The image  shows a wheel with…

Q: 1- Sketch front, right and top views of the following object. Each grid represents 10 mm. Front

A: Given: Sketch Front, top and right side view of the given isometric view.

Q: 3 show all steps in detail, units and formulas please.

A:

Q: I need help matching the following terms to the phrase it describes. Answers are used only once.

A: The correct answers are matched for the corresponding terms as shown below:

Q: sketch the 2d figure using autocad and colour the hatching and reference lines

A:

Q: On the first picture, you have the length of the triangle as 300. If the total length of the door is…

A: Here you are asking why the length of the triangle is 300 and not 440.

Q: Given the figure attached, Determine the following: A) What is magnitude of Rand Cr in pt D? (Unit…

A: Solution: Given Data:

Q: Draw the orthographic Projections of given object.

A: Orthographic projections are projections of a component in three directions that are perpendicular…

Q: Rotate the objects shown below by the indicated amount and sketch the result in the space provided.…

A:

Free Body Diagram

The system of forces acting on a body tends to either rotate it or make the body undergo motion. In general, when an external agent exerts a force on a body, the body undergoes translational motion and rotational motion. The body has six degrees of freedom under the influence of that force. Here, three degrees of freedom are from the translational motion while the other three are from the rotation motion. However, sometimes the bodies are not allowed to undergo any motion and are fixed, under such conditions the body is said to be constrained.