Determine the x-, y-, and z-coordinates of the mass center of the body constructed of three pieces of uniform thin plate whichare welded together.Answers:x=y=Z=iMO365 mmZ355 mm60 mmmmmmmm155mm130 mm215 mm

Solution: Assume t = 10 mm Compute the volume: V1=12×365×345×10=629625 mm3 V2=510×345×10=1759500 mm3…

Answered: Determine the x-, y-, and z-coordinates…

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter8: Engineering Materials

Section: Chapter Questions

Problem 7ETSQ

See similar textbooks

Similar questions

The stress-strain relation shown in figure below was obtained during the tensile test of an aluminum alloy specimen. Picture1(3).jpg 60,000 40,000 20,000 0.002 0.004 0.006 0.008 Strain, in./in. Copyright ©2017 Pearson Education, All Rights Reserved Determine tangent modulus at a stress of 45,000 psi in same unit (psi). Stress, psi
Two steel plates are welded to a rolled W section as indicated. If the area and the centroid location of each subsection are given in the table below, what is the moment of inertia with respect to x axis? (Height of W14x38 section is 14.1 inches.)
Draw the Maxwell Diagram of the given truss. Pls, indicate the scale. 1000 lb 2000 lb 1000 lb 2000 lb E 1000 lb G. 2000 lb 6 8 1000 Ib 1000 lb 1000 lb 4 10 i 12 13 2 3 60° 60° 11 301 MATHalino.com 30 A R3 N 2000 lb 2000 IbY 60 ft K R1 R2
The thin uniform plate shown has a mass of 100kg and is subjected to a force and couple momentalong its edges. If it is supported in the horizontalplane by a roller at A, a ball-and-socket joint at B,and a cord at C, determine the components ofreaction at these supports to maintain equilibrium. Please provide all written work and show FBD. Thank you!
Find the required properties for the following sections The area of W33X130 in mm? • The moment of inertia about the x-axis for W10X112 in mm“ The radius of gyration of L50X50X3 along the x-axis in mm The distance from the outer face of the web to the centroid of C6X13 in mm The elastic section modulus of C9X20 about the y-axis in mm3
• Calculate all two force members of the plane • Vertical Support at A and D -Include direction (upward, downward, N, E, W, S, or if Tensile or Compressive -Include 4 decimal points -Provide a readable solution -
Q2/Show the mechanical properties changes during tensile test of a metal specimen. Write the mathematical relationships. 443X
a) For the solid section shown in Figure Q1, determine dimensions a, b and c. b) Determine the centroid position (x, y) for the solid section shown in Figure Q1 relative to the origin O on the x-y axes. Clearly show the breakdown of the section into areas used in your calculations. y 85 mm 53 mm b 25 mm 157° 25 mm 65 mm Figure Q1 (Not to scale) X
The lower ends of the 3 bars in the figure are at the same level before the rigid homogenous 18Mg block is attached. Each steel bar has an area of 566mm^2 and E=200Gpa. For the bronze barn the area is 866mm^2 and E=83Gpa. Find the stresses developed in each bar.
Determine the cross-sectional area of the bronze rod (in mm)? 2m 3m 60 kN Ns mm IS mm 3D bronze rod
I need help with a. & b. I don't understand what is meant by "one scale from zero to about 0.02 in/in" in part a
Q5 A specimen of magnesium having a rectangular cross section of dimensions (3.2 mm X 19.1 mm) and gage length 63.5 mm is deformed in tension. Using the load-elongation data tabulated as follows load (N) and Extension (mm), Find the standard mechanical properties. load 1380 2780 5630 7430 8140 9870 12850 | 14100 14340 13830 12500 Ext. 0.03 0.06 0.12 0.2 0.25 0.64 1.91 3.18 4.45 5.72 6.99 a) Draw the stress strain curve. b) Find the young modulus. c) Find the proof stress d) Find the ultimate tensile strength. e) Find the fracture stress f) Find the maximum strain.

SEE MORE QUESTIONS

Recommended textbooks for you

Materials Science And Engineering Properties

Civil Engineering

ISBN:

9781111988609

Author:

Charles Gilmore

Publisher:

Cengage Learning

Materials Science And Engineering Properties

Civil Engineering

ISBN:

9781111988609

Author:

Charles Gilmore

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

Determine the x-, y-, and z-coordinates of the mass center of the body constructed of three pieces of uniform thin plate which are welded together. Answers: X = y= IN i IM i 365 mm -355 mm 60 mm mm mm mm 155 mm 130 mm 215 mm