Determine the x- and y-coordinates of the centroid of the shaded area. 50 150 - 50 -170-

Q: QUESTION 2 Solve the following differential equation in Matlab using ode45.m. Use time interval of…

A: The initial conditions are,To find:The solution of the given differential equation using the…

Q: Problem 3) Given the period T = 1.2 day, find the frequency in Hz. Provide your answer in Hz to the…

A: Given data  Period = 1.2 day Find the frequency in Hz First convert period day to seconds.

Q: On the part below, with only the limits of size specified, what coaxiality tolerance is implied…

A: In this problem, it is asking about the co-axially tolerance between the two diameters.

Q: 4) The measured free vibration response of a one-degree-of-freedom system is as shown in the below…

A:

Q: 01 F1 A L/2 F2 02 B L/2 L = 3.00 m F1 = 12.0 N F2 = 16.0 N F3 = 20.0 N 01 = 70.00 02 = 25.00 03 =…

A: Given:L = 3 mF1 = 12 N, F2 = 16 N, F3 = 20 N70°, 25°, 10°Required:TB ( torque about the point B )

Q: Find the period of the oscillator's response (period of the slow sine) for w =10. Round your answer…

A:

Q: Q28- In this figure F=400 N₁ F3=300N Find F4 and F2? Note that the figure in equilibrium F4 પડ 30°…

A:

Q: A rectangular block 100 mm x 150 mm has a hole with diameter 60 mm at the center. The hole tolerance…

A:

Q: A tachometer has an analog display dial graduated in 5‐revolutions‐per‐minute (rpm) increments. The…

A: The amount of uncertainty that exists during the early phases of a design process is referred to as…

Q: ne 1/2-inch diameter pin in the drawing below is required to be perp ature A within tolerance of…

A: A feature control frame is used to show the conditions and tolerances of the dimension of the part…

Q: The table gives data concerning the shrink fit of two cylinders of differing materials and…

A:

Q: I need help with question number 15 that is pertaining to the print provided.

A: 15.The unidirectional system is used here for the dimension placing. The unidirectional system is…

Q: For a certain engine havI a flywheel approximated as a solid disc, is required for keeping the…

A: we have to determine the mass of the flywheel

Q: What are the values of each variable? Show complete solution

A:

Q: 3. If the tolerance applies at MMC then a possible O indeterminant bonus O LMC zero tolerance…

A: given = fill in the blanks

Q: Read the peak power and peak torque from the following curve. Also, find the engine speed that the…

A:

Q: Q1/B: A four-cylinder four-stroke SI engine has an output of 65 kW at 2500 rpm. A Morse test is…

A: Given: The power output, P = 65 kWThe speed of the engine, N = 2500 rpm

Q: QUESTION 1 Solve the following differential equation in Matlab using ode45.m. Use time interval of…

A: To solve the given differential equation in MATLAB using `ode45.m`, we can follow these steps:1.…

Q: 3. Microfluidic channels will need to be fabricated on a key micro-scale sensor used by aerospace…

A:

Conservation of Energy

In physics, the rule of the conservation of energy states that energy doesn’t disappear from the atmosphere; instead, it changes its form from one type to another. Energy is one of the most important physical quantities in nature, and it cannot be created or destroyed — only transformed.