Determine the theoretical nominal moment capacity of the beam shown if fy = 420 MPa and fc' = 28 MPa. %3D 620 750 5-30mm 65 65 400 Dimensions are in millimeters

Q: The floor slab usually refers to a slab that has been formed using concrete and generally steel…

A: Suspended Slab : These type of slabs are not in direct contact with the ground. The roofs and floors…

Q: Determine the cost of total earthwork of a highway section having the cumulative volume shown in the…

A: Given -  OVERHAUL COST - 650 ID/m3 BORROW COST - 2500 ID/m3 Free haul cost = 1250 ID/m3 FREE HAUL…

Q: When will you plan for stockpiling of excavation soil

A: The flow of fluid includes movement of an unbalanced fluid. As long as unequalled forces are in…

Q: you have contracted to construct a swimming pool in a residential area. through your site…

A: The construction of swimming pool in the expansive soil is difficult as it causes damage to the…

Q: Q2: - A factory is to be built on a ground having following elevation and the area bounded by each…

A:

Q: what are the significance of specific gravity and Blaine fineness tests

A: Specific gravity  The correct definition of specific gravity (sg) is the ratio of a substance's…

Q: Question 1 A rectangular building with a length of 50' and a width of 30' that is 16" wide and 8"…

A: Given  Length = 50 ft  Width= 30 ft

Q: 1.) The most accurate source of data is national standards books. true or false 2.) The geometric…

A: 1) if we consider the Engineering data, then the national standard books like national standard…

Q: Explain The consolidated-undrained (CD) test

A: In the soil mechanics find the mechanicals properties of soil like shear strength, permeability and…

Q: Calculate the dead load of a R.C.C. slab Size of the Slab is 3.0mt by 5.0 mt., Thick ness is 12 cm.…

A:

Q: The cross-section notes shown below are for a ground excavation for a 12m wide roadway. STA 12+1400…

A:

Q: You have been contracted to construct a swimming pool in a residential area.Through your site…

A: Expansive soils are those type of soils which represent a large change in volume due to change in…

Q: During concrete pavement inspection of link (3*10) slabs, from airfield section, 4 slabs medium, 12…

A:

Q: Define the Purkaystha and Char reduction factor method ?

A: The purkaystha and char reduction factor is used to find bearing capacity of foundation on…

Q: Explain the Estimating Soil Modulus from SPT and CPT ?

A: SPT is used for calculating  young's modulus Soil stiffness is directly affected by connections of…

Q: 49. What is the problem of rehabilitation? A. Unique B. O Submerged C. O Lined D. O Layered

A:

Q: black box testing?

A: Black-box testing is a method of software testing that examines the functionality of an application…

Q: What is a two-peg test, how is it conducted?

A: Two peg test checks wheather dumpy level is capable of showing true horizontal reading or not and if…

Q: Define the techniques of Soil Analysis?

A: Soil analysis determines the content of basic plant nutrients, nitrogen, phosphorus, potassium, pH…

Q: What is well graded soil?

A: Types of soil:In general, the soil is classified as “coarse grained soil” and “fine grained soil”.…

Q: close You have been contracted to construct a swimming pool in a residential area, Through your site…

A: Expansive soils are the one which undergoes rapid volume change like they swell too much and shrink…

Q: Describe Mohr’s Failure Criterion?

A: The theory of Mohr implies that failure occurs once the circle of Mohr reaches the envelope provided…

Q: Describe 3 applications of failure Analysi

A: Step: 1 Analysis: - It is a process in which one will do detailed examination of different parts of…

Q: How to determine the design service load for use in SLS analyses?

A: The limit state design method is the best effective method in the design of RCC and the steel…

Q: If you are given a project to build a high-rise building on a limestone and granitic area, assess…

A: Brief concept- High rise buildings- High-rise structures are tall enough to necessitate the use of…

Q: What is soil set-up factor?

A: The bearing capacity is the major factor in the geotechnical engineering. The scientists have…

Q: Describe how the process of segmentation works on the most fundamental level. What makes it distinct…

A: Introduction- Process of segmentation- There are 5 steps in the segmentation process:1) segment…

Q: If the excavation depth is about 5ft and the soil is cohesive, where the site area is adjoining…

A: If sloping or benching is utilized as the support system during excavation, the slope of excavations…

Q: The field engineer on a highway construction was left alone when the supplier of filling materials…

A: For calculating the volume of earthwork  total area is divided into no. of  cross sections and area…

Q: Q1: In construction of a highway section, the earthwork information is available as shown in the…

A: Given - Free haul distance = 500m  Swelling factor = 20%  Overhaul price = $200/m3 To find -Mass…

Q: Sample resume of Civil Engineer

A: SURYA CHARITHA  Sometown, TSS 48103 Phone: (000) 000-0000          Email: ab@somedomain.com…

Q: You have been contracted to construct a swimming pool in a residential area, through your site…

A: The construction on an expensive soil is most critical construction as it may cause a heavy damage…

Q: There are 3 ways to protect against trenching hazards. Which one of the following is not a method? O…

A: Trenching is technique of excavtion in ground . The depth of excavation is deeper than its width .…

Q: Where does The SPT-T procedure can be used?

A: This test incorporates the advantages of the Standard Penetration Test (SPT) and the Vane Shear Test…

Q: You have been constructed to conduct a swimming pool in a residential area. Through your site…

A: It is very dangerous to construct any structure over expansive soil from safety and stability point…

Q: When costs are being estimated for alternative structural configurations and design concepts, the…

A:

Design of structures using FEA

An arrangement, in which various members are interconnected with their constrained relative motion, the whole arrangement is then known as a structure. The degree of freedom of such a structure is zero. In such a structure, the load can act throughout the length of the structure or at the joints.