Calculate the dead load of a R.C.C. slab Size of the Slab is 3.0mt by 5.0 mt., Thick ness is 12 cm. Calculate the dead load of slab length width thickness Volume Density of R.C.C. slab Dead load 5.0 MT 3.0 MT. .12 MT. 5.0 X 3.0 X.12 2400 kg/cm3 1.8 X 2400 1.8 cm3 4320 kg

Calculate the dead load of a R.C.C. slab Size of the Slab is 3.0mt by 5.0 mt., Thick ness is 12 cm. Calculate the dead load of slab length width thickness Volume Density of R.C.C. slab Dead load 5.0 MT 3.0 MT. .12 MT. 5.0 X 3.0 X.12 2400 kg/cm3 1.8 X 2400 1.8 cm3 4320 kg

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: One way slabs are those that bend along the short span only while two way slabs are those that bend…

A: Given data in question One way slab Two way slab To find out True or false

Q: Find Wn for the shown slab when M- ve=2Mn and M+ve=Mn for the shown slab use Yield Line Theory XX…

Q: 09/ bounded triangle slab region shown in Figure, if we suppose the deflection equation of the slab…

Q: This question contains 2 different scenario: a. If FA = 38 kN and FB = 45 kN, determine the…

Q: How do we compute for the minimum thickness of slabs? What are the four (4) considerations…

Q: A plate load test is carried out on a 45 cm square plate at a depth of 3 m below ground surface on a…

A: Given data:- Load Intensity (t/m2) Settlement(mm) 10 3 20 5 30 7 40 9 50 15 60 22…

Q: 1-Explain about two-way slab with neat diagram. 2- Write all the assumptions made in theory of pure…

A: Solution: NOTE: Due to time confinement I could not answer all questions also as per the policy of…

Q: A plate-bearing test using a 30-inch diameter rigid plate was made on a subgrade as well as on 10…

A: Given : Dia of rigid plate - 30 inches Thickness of gravel base = 10 inches The unit load required…

Q: A 100lb block with a wide base is pulled by a force P and us=0.4. Which force orientation requires…

Q: Question 6 To ensure stability, foundations must provide an adequate factor of safety against shear…

A: Given data in question Stress variation under the foundationVarious zonesStress comes upto the depth…

Q: ASAP NEED IN 1 HOUR I'LL GIVE UPVOTE Design a 3.66 m simply supported slab to carry a uniform dead…

Q: Q:: Using fc'-25 MPa, fy 420 MPa, self- weight neglected, Wu on slab is 25 kN/m2 to answer the…

A: first, find the slab thickness using minimum slab thickness then find the minimum reinforcement…

Q: Calculate the design moments of two-way slab as shown with a dimension of 4 mx 6 m if it is to…

A: Shorter span of slab, S=4mLonger span of slab, L=6mDL=10 KPaLL=3.2 KPaOne short and One long edge…

Q: Topic: HOLLOW BLOCK SLAB Determine the total dead load (in kPa) of the following different types of…

A: We have to determine the value of total dead load:-

Q: In a highway construction site, excavation with sloping is planned for soils with an unconfined…

A: According to Occupational Safety and Health Administration, soil are classified into 4 categories…

Q: Calculate the Load distribution of slabs to beams 3, 4 and C using 10kPa load multiplied by the…

Q: 1.Design and detail a one way simply supported slab whose clear span length is 3.8 m. Take Live load…

A: clear span =3.8mlive load=3 KN/m2floar finish load=1.2 KN/m2assume the depth=230mmbs=230mmpt=0.35%…

Q: rom the face of the foundation footing the above N 10 -15M rebar in a continuous concret

A: ANS (11) TRUE

Q: Explain the importance of California Bearing Ratio test?

A: California Bearing Ratio (CBR):CBR is the ratio of force required per unit area to penetrate a soil…

Q: Calculate the Load distribution of slabs to beams 2, C and D using 10kPa load multiplied by the…

A: First we have to divide the slab area in to different parts. Then multiply the area around that…

Q: Design using the yield-line theory a rectangular slab panel of size 4 m by 5.5 m, h is continuous…

Q: A rectangular footing has a footprint of 16ft x 20 ft. If the footing carries a load of 160 tons at…

Q: Q2) For the column layout shown in Figure (2), find the plan dimensions of a combined footing and…

A: Solution; The values provided in the question are as follows: Soil allowable bearing capacity…

Q: A contact radius of dual tires is 3.25 in with a total load of 1050o Ib, center to center spacing…

A: Given data- Total load = 10500 lb Contact radius of dual tires (d) = 3.25 inch Centre to center…

Q: What is the required minimum thickness (mm) of a 5m long both-end continuous, one-way slab if its…

A: Span length, L= 5m Steel rebar yield strength, Fy= 420 MPA Both ends continuous

Q: 19- There are three steps in the substructure approach. Which one is not one of them? a) Direct…

A: The direct method, as well as the substructure methodology, are two main kinds of soil-structure…

Q: Q3: For the solid slabs shown in Fig.(3), find the spacing of ( 12 mm ) bars required at the…

A: The slab is an important element in the structure for carrying floor load and another live load that…

Q: All Two simply supported slabs: square and circular. They are istropically reinforced and subjected…

Q: Explain the importance of California Bearing Ratio test?

A: Importance of conducting CBR Test:- California Bearing Ratio test is actually performed for…

Q: Calculate the Load distribution of slabs to beams 2, C and D using 10kPa load multiplied by the…

Q: each cut volume in earth work must be adjustment for * O bulking shrinkage O both for shrinkage and…

A: Given data: Each cut volume in earth work must be adjusted for. a)bulking b) shrinkage c)both for…

Q: Determine the increase in vertical stress directly below the center of the footing

A: Load (q) = 14506 lbs/ftwidth of footing = 2.3 ftdepth of footing (z) = 0.8 ftNeed to findThe…

Q: By using Ultimate Strength Design Method, design the slab showing in the figure below for the…

A: In the event that length and width ratio, the extent is more conspicuous than or comparable 2 or…

Q: Q1.: Calculate the amount of (cement+ sand+ gravel) for foundation below: If concreate grade M25 (2)…

A: Given: Section of foundation: 0.5 m x 1 m Grade of concrete: M25 (1:4:8) To find: The quantity of…

Q: Design one-Way Slabs; with EX: Design Reinforced concrete slab monol thic beams, Show in fig. below.…

Q: 4.2. Using the coefficient method, design a (case 3) cantilever slab (thickness and reinforcements)…

A: L1=4m L2=3m LL=6.69kPa DL=2.5kPa fc=21MPa fy=276MPa

Q: Determine the reinforcements for given slab systems and draw a sketch to show bar arrangements hf=12…

A: height of the flange, hf = 120 mm Unit weight of concrete, γc=25 kN/m3 Plaster = 1.5 kN/m2 Load on a…

Q: Design a one way slab to carry a live load of 4500Pa and a dead load of 3525Pa. The slab has a…

Q: 12- Calculate the net allowable soil stress of a soll with allowable stress 300 kN/m2 in the depth…

A: Allowable stress of the soil Depth from the soil surface to the footing (h1) = 2.50 m Height of the…

Q: Give me right answer with short explanation. Which of the following statements about the Hillerborg…

A: Brief concept- Hillerborg strip method of design for concrete slabs- This method is used for the…

Q: The impact of grades is much higher on passenger car than trucks true or false?

A: False

Q: Problem #2: Design a (One Way Slab) slab whose clear length is 20 ft x 12 ft which is subjected to a…

A: Clear length of a slab = 20 ft x 12 ft Live distributed load = 150 psf It is asked to Design a One…

Q: Considering the rectangular section with the given concrete dimensions (in mm) shown below in Figure…

A: (a) Given Pf = 850 kN , My = 620 kN.m fc’= 25 MPa , fy = 400 MPa concrete cover (dc) = 50 mm from…

Q: Puncturing Object * relatively large * relatively small ded & relatively large ded & relatively…

A: According to given data

Q: Calculate the Load distribution of slabs to beams 2, 3 and A using 10kPa load multiplied by the…

Q: Problem # 2 The slab shown is unsupported along the longer edge and fixed on all the other sides.…

Concept explainers

Methods to Determine Vertical Stress

The load applied to the soil is transferred to the underground. The presence of water at soil pores and solid grains above the soil are the primary components that are responsible for the effective load transfer. Due to the load acting, the internal component of the soil or the underground formations undergoes deformations or a tectonic shift. The amount of deformation depends upon the amount of load acting on the soil surface, which indeed, depends on the weight of everything present above the soil. Due to this, the underground soil element develops internal stresses which try to resist the tectonic changes.

Question

Calculate the dead load of a R.C.C. slab
Size of the Slab is 3.0mt by 5.0 mt., Thick ness is 12 cm.
Calculate the dead load of slab
length
width
thickness
Volume
Density of R.C.C.
slab
Dead load
5.0 MT
3.0 MT.
.12 MT.
5.0 X 3.0 X.12
2400 kg/cm3
1.8 X 2400
1.8 cm3
4320 kg

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine the reinforcements for given slab systems and draw a sketch to show bar arrangements 44 + -12 cm 3.25 1.50 h=120 mm Q=2.0 kN/m² (for Slabs) Q=5.0 kN/m² (for Balcony) -12 cm 3.35 1.50 0.25 ++ + =12 cm 325 150 0.25 ++ + 12 cm 3.25 3.50 Yconcrete 25 kN/m³ Coverage+plaster= 1.5 kN/m² Materials: C25/S420
A simply supported 1 way slab having span of 3 meters is to carry the load for DL = 5kpa and LL = 4.8Kpa. If the concrete f'c = 28Mpa and rebar to be used is 10mm with fy = 276Mpa. a.) Determine the minimum thickness of the 1 way slab.(answer in millimeter in whole number) b.) Determine the Ultimate loading combination for the slab considering 1 meter strip?(answer in KN/m. in 3 decimal places ) c.) Determine the Ultimate moment for the slab considering 1 meter strip?(answer in KN-m. in 3 decimal places) d.) Determine the effective depth of the slab considering concrete cover = 20mmanswer in millimeter. in whole number e.) Determine the area of reinforcement for the slab based on the actual loadings.(answer in sq.mm. in 3 decimal places) f.) Determine the spacing of the rebar.(answer in millimeter(Don't round up, use actual value). in 3 decimal places)
Explain the Triaxial compression test representations.
H.W.1: One-Way Slab: 1. Check slab thíckness. 2.Check shear force. 3.Design flexural reinforcement for the slab. I 4.Dosign flexural roinforcement for continuous beam B. fe=28Mpa 6m 5.8m 5.8m 6m f,-420Mpa Slab h=250mm 6m Beam Section: ha600mm bw#350mm Column Section: 500x500mm 7m LL=5kN/m? Exterior D.L-4kN/m? 7m K
Calculate the Load distribution of slabs to beams 3, 4 and C using 10kPa load multiplied by the tributary width. Colored box represents columns and uncolored represents beams.
Quantity Surveying. Plz, answer all the question parts.
Please solve completely and give stepwise solution. ACI- 318 Question:2 A one-way slab is supporting a uniform service dead load (excluding self-weight) of 50 psf and a uniform service live load of 40 psf as shown in Fig. 02. It is required to; (a) Analyze the given slab for flexure. (b) Design the given slab for flexure. Use only # 4 bar for flexure. Take fe' = 3 ksi and fy = 40 ksi. 12" Slab 12.75' Figure 02.
QUESTION 40 1. Transient analysis and limit stability analysis mean the same thing and thus can be used interchangeably. True False QUESTION 41 1. Tension cracks would usually occur first on the ground surface thus indicating the onset of slope instability. True False QUESTION 43 1. The retaining wall worked as a barrier against excessive groundwater loss and safeguarded the buildings located behind it. True False QUESTION 30 1. The sea water level causes the groundwater table to fluctuate on site. True False
In the given 20.0 meter slab and inclined 10 owith the horizontal, the ends are resting on inclines of 35 degreesincline at B and 25 degrees at A, a semi-trailer truck is to pass through it with the wheel loads as shown. How Far (x, meters) shall be the front wheels located before motion impends, the angle of friction is 18 o for all areas of contact. If the weight of the slab is to be neglected. Use 3 Decimel Places
Complete answer
Question 8 A sample slab section view is shown below: *4 0 10" EW 30 Felt Joint El. See What should be the correct reinforcement configuration in plan view for this slab? What should be the correct reinforcement configuration in plan view for this slab? 10" 10" 10" 10"- #4 bars 10"- 10" 10" 10" #4 bars 10"- # 4 bars 10"-
QUESTION 2 A square column with side dimension of 20 mm rests on top of a timber footing. It is determined that the column carries an axial load of 591 kN. If the punching strength of concrete is 19.86 MPa, determine the minimum thickness (mm) of the footing.