This question contains 2 different scenario: a. If FA = 38 kN and FB = 45 kN, determine the magnitude of the resultant force and specify the location of its point of application (x,y) on the slab. b. If the resultant force is required to act at the center of the slab, determine the magnitude of the column loading FA and FB and the magnitude of the resultant force

Q: The $40 mm round steel shaft shown below is subjected to a bending moment of 1.6 kN-m and a torsion…

A: Steel shafts, which are often composed of carbon steel but can sometimes occasionally be constructed…

Q: W1 b. C 1.75 m d 5.00 m W4 kN/m W2 5 kN/m P 15 kN 1.25 m b 2.00 m Given: a

A:

Q: A shear force of V = 410 kN is applied to the box. The wall thickness is 13 mm. Using thin wall…

A: The Shear Force will induce a shear flow in the box. For a thin walled box structure, the shear flow…

Q: Sketch all the possible yield line pattern for the slabs shown in Figure Q2(a). All supports are…

A:

Q: haft AB and CD are solid and of diameter d, while shaft BC is hollow with inner diameter 80 mm and…

A: Given that:

Q: A timber beam 98 mm wide by 160 mm high is subjected to a vertical shear V = 29 kN. Determine the…

A: Draw the diagram as follows.

Q: For the simply supported beam shown below, determine the internal resultant loadings at a point 1…

A:

Q: View Policies Show Attempt History Three solid bars, each with square cross sections, make up the…

A:

Q: machine supporting structure consists of a hollow pipe of external diameter200 mm and wall thickness…

A:

Q: 1. For the beam shown, a. determine the maximum flexural stresses in compression ant tension. b.…

A:

Q: Find the an equivalent resultant force and specify the location (x,y) of the equivalent resultant…

A: Consider the figure,

Q: A simply supported beam is post-tensioned by a straight tendon with an initial prestressing force of…

A: Given that,Span of the beam, L=15m. Effective prestressing force, P=2000kN. LOAD's acting on the…

Q: 1–52. The bar has a cross-sectional area of 400(106) m². If it is subjected to a uniform axial…

A:

Q: The service loads acting on a structural member are as follows: DL = 80 kN/m; WL = 50 kN/m The limit…

A:

Q: A B C D A circular beam of 100 mm diameter is subjected to a shear force of 30 kN. The maximum shear…

A: Given- Diameter d=100 mm,shear force =30 kN The maximum shear stress?

Q: The measured strains for an equiangular rosette, attached to a stressed aluminum alloy member,are E0…

A: Consider the given data…

Q: For a simply supported prestressed concrete beam, compute the stress in the bottom fiber at beam…

A:

Q: QI: For the foundation shown in the figure below, find the stress increment under point B at depth z…

A: The vertical stress increment at any depth z and at radial distance r from the point of action of…

Q: Consider a circular beam 8 m long and 600 mm in diameter subjected to uniformly distributed load of…

A: For given circular beam,Length,L= 8 mDiameter, D= 600 mmLoading, 30 kN/m uniformly distributed load

Q: The extruded plastic shape will be subjected to an internal shear force of V- 260 lb. Dimensions of…

A: Given : Internal shear force, V = 260 lbDimensions : b = 1.7 in                         d = 3.4 in…

Q: The figure shown below is a hollow pre-cast beam designed for a shopping mart somewhere in Cubao.…

A: Working stress method:In this method, materials are fully utilized in designing any member. It shows…

Q: View Policies Current Attempt in Progress Two solid bars support a load Pas shown. Bar (1) has a…

A:

Q: A simply supported beam, 0.05 m in wide by 0.1 m in high and 4 m long is subjected to a concentrated…

A: The flexural strength is the maximum bending stress that can be applied to the material the tends to…

Q: pls answer ASAP, I'll rate. Thank you so much. Using the Method of consistent deformation determine…

A:

Q: Q- In LSM instead of 0.002 strain in parabolic stress section, it is assumed that new strain for…

A: Given- In LSM instead of 0.002 strain in parabolic stress section, New strain for parabolic stress…

Q: The beam seciton shown below has moment of inertia about its neutral axis: I = 301.3 (10 -6)m 4 ,…

A: Figure is given in the question

Q: yield stress is 12 MPa and a factor of safety of 1.5 inst yielding is desired, what is the required…

A:

Q: A W310 x 38.7 standard steel shape is used to support the loads shown on the bearn in the figure.…

A:

Q: determine the safe concentrated load that the 150 mm x 350 mm cantilever beam could carry located at…

A: Determine the safe concentrated load that the 150 mm x 350 mm cantilever beam could carry

Q: A simply supported beam, 2.5 in wide by 5 in high and 10 ft long is subjected to a concentrated load…

A: Width of beam (b) = 2.5 in Depth of beam (d) = 5 inSpan of beam (L) = 10ftConcentrated load (P) =…

Q: Please calculate the following for the following problems. Please show all the work with…

A:

Q: For a simply supported prestressed concrete beam, compute the stress in the top fiber at the…

A:

Q: n in the figure. calculate the maximum bending stress (in Pa) if P = 4141 N, W = 1010 N/m, a = 1.15…

A:

Mechanics of Solids

It is the study of the behavior of solid materials, their characteristics under various circumstances such as variation in external forces, temperature, and other internal factors. It is one of most important study in the field of engineering science, especially chemistry and mechanical engineering. In rigid body, the idealization of the solid body in which deformation is neglected. Deformation is known as the force acting on the solid state system which exerts change in its shape of the body but it continues to be at rest or in a uniform motion but it cannot accelerate. But those solid systems do have elasticity, compressibility and can be bent. This field is very vast since there are wide range of materials around us.