Determine the stress of the compression steel.200나 6020mm45032mm60A95.64B40.784.7890.858D.

Solution: Values are not given such as fc, fy. let as assume the values which are not given

Answered: Determine the stress of the compression…

Engineering

Civil Engineering

Determine the stress of the compression steel.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Aluminum Steel hs composite beam of aluminum (F. = 70 GPa) and steel (F. = 190

Q: The three-member truss is used to support vertical load P. If P=200 kN, find the stress of members…

Q: ASSUME THAT THE TRUSS IS SIMPLY SUPPORTED AT JOINTS M AND E. Determine the stress at member CD if Pu…

A: Given data in question Area Length Dimensions Loading To find out Stress in member CD Note We…

Q: Is this a frame or a truss? Calculate the cross section of the bar BC if the allowable normal stress…

A: Given:- Allowable normal stress in BC = 165 MPa To determine- a) Is this a frame or a truss? b)…

Q: 22) One brass bar and one steel bar are forming the setup shown below. Determine the tresses and the…

Q: copper tubes 0.20cm thick. The three tubes are joined together at their ends. What is the maximum…

A: Given : 1. Outside Diameter(D1) = 3cm 2. Thickness (t) = 0.25cm 3. Inside Diameter (D1) = D2-2t =…

Q: 1. See figure below and solve for the maximum value of torque the composite shaft can accommodate…

A: Given data Bronze G = 6x10³ ksi Steel G = 12 x 10³ ksi Max Shear stress in bronze = 8 Ksi Max Shear…

Q: 3 ft 4 ft 7. The 2P P Aluminum A = 0.6 in.2 E = 10 x 10° psį Steel - A = 0.4 in.2 E = 29 x 106 psi…

Q: A steel rod having a cross-sectional area of 324 mm2 and is 10 m long .The rod is loading by tensile…

A: Given: The cross-sectional area is 324 mm2. The length of the rod is 10 m. The tensile force is 31…

Q: SOLIO CYLINDRICAL RODS AB and BC are welded together at B and loaded as shown. Knowing that the…

A: Given data - LAB = 30 in LBC = 25 in Allowable normal stress = 2.5 ksi Find out - Smallest allowable…

Q: The two vertical rods attached to the light rigid bar are identical except for ength. Before the…

Q: For the section shown, if n 3, N.A is %3D at 58 mm from top, I = 74 x 10^6 mm^4 and the normal…

Q: A rectangular steel block is 300 mm in the x direction, 200 mm in the y direction, and 150 mm in the…

A: Stress: Stress is defined as the deformation offered by the internal forces on the body. And it is…

Q: - A joint is made by gluing two plywood gussets of thickness to wood boards. The tensile working…

A: The tensile working stresses for the plywood is 1200 psi.The tensile working stress for the wood…

Q: u = -c(y² + væ), v = 2cxy |

A: Given:- u=-c(y2+vx) v=2cxy c=constant v=Poisson's Ratio To find:- stresses

Q: G K H

A: Given data:

Q: 0,3in 0.4in2 3P 2P + C. Find the albwable säfe p if the stresses in the bar are the following: AB 50…

Q: 3. A steel baris l0mm diamelex and am lo It is stretched with a force of 20kN and exteads by 0-2mm-…

Q: The member shown in the right side consists of the steel rod AB that is screwed into the end of the…

Q: A beam is reinforced for tension only unless its required steel ratio is _________ the maximum steel…

Q: The composite shaft consists of a mid-section that includes the 25-mm-diameter solid shaft and a…

Q: Answer this using method of joints. Show your clear, detailed, and whole solution. Don’t mind the…

Q: please

Q: Two members, 1 and 2, are subjected to thermal stress. Determine the total deformation of member 1…

A: There will be compression stress in both bars.

Q: The composite shaft consists of a mid-section that includes the 25-mm-diameter solid shaft and a…

A: T= 1000 Nm = 1000000 Nmm G=75 GPa = 75000 N/mm2

Q: 7. Determine the normal stresses on the plane whose normal is at 35° with the x-axis. a. 50.65 MPa…

A: To find normal and shear stress

Q: A composite beam is made of two brass [E = 115 GPa] plates bonded to an aluminum [E = 65 GPa] bar,…

Q: Determine the stress at member FE if Pu = 18.375 Kips, the area is 11 in?. Answer your problem with…

A: Given data in question Loads Dimensions of truss Span member length Area To find out Stress in…

Q: 3. The manufactures wood beam carries a uniformly distributed load of intensity Wo Determine the…

A: Shear stress in the wood is limited to 300 psi.

Q: A W18x40 standard steel shape is used to support the loads shown on the beam. Assume P= 26 kips, w =…

Q: two steel plates are bolted to the wooden beam shown by 30-mm-diameter bolts spaced at 200 mm.…

A: Find modular ratio:n=EwEs=40200=15so,Reduced width of wood =1505=30mmFInd…

Q: A composite beam is made of two brass [E = 106 GPa] plates bonded to an aluminum [E = 60 GPa] bar,…

A: Beam of Composite Section have applied Bending moment and Calculation of Bending stress in Aluminum…

Q: 1. Differentiate the permanent and the variable action with suitable examples

A: Actions are classified in Eurocode : EN 1991. 1) Permanent action 2) Variable action 3) Accidental…

Q: 1. The assembly is shown is attached to supports at A and D. Section BCD is a solid 2" diameter…

Q: D. A DD mm radius Steel is subjected to tensile test. Determine its yield and ultimate load it can…

Concept explainers

Moments

There are various practical applications of the concept of moments, like a rotation of the crank due to linear motion of the piston, the moment of inertia and its use in designing beams and columns, bending moment concept, torque, twisting moment, etc.

Question

Determine the stress of the compression steel.
200
나 60
20mm
450
32mm
60
A
95.64
B
40.78
4.78
90.858
D.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine the stress at locations A, B, C, D, E and F N1=7 N2=0
Two members, 1 and 2, are subjected to thermal stress. Determine the compressive force acting on the members. (in kN) AT =30 °C X=1|,7 XID%. a = 17:3X10% L-2,5M L-3.sm E= 200GPA E: 70 Gla regular hexagon hollow circle each side : 15omm douter 150 mm dinner = 50 mm
Find the moment of resistance of the section. The permissible stresses are 10 N/mm2 in tension and 16 N/mm2 in compression. 200 mm 400 mm 400 mm
The composite bar shown is firmly attached to unyielding supports. An axial load P= 200 kN is applied at 20°C. Assume a = 11.7 um/(m °C) for steel and 23.0 um'(m °C) for aluminum. Find the reaction at the left support. a. find the reaction at the left supportb.find the stress at the steelc. find the stress at the aluminum
(a) Explain difference between slow sand filter and rapid sand filter.(b) Explain difference between lime soda process and zeolite process.
Please give handwriting solution
Knowing that the allowable stress in section a-a is 90 MPa, determine the largest force that can be exerted by the press shown. The largest force that can be exerted by the press is
A rectangular steel block is 75 mm in the x-direction, 50 mm in the y-direction and 100 mm in the z direction. The block is subjected to triaxial loading consisting of three uniformly forces as follows: KN tension in the x-direction, 250 KN compression in the y-direction, and 240 KN tension in the z-direction. If u = 0.3 andE = 200 GPa, Determine the total resulting strain in the x- direction. %3D
AW18 x 40 standard steel shape is used to support the loads shown on the beam. Assume P = 15 kips, w = 4.0 kips/ft, LAB = 3.2 ft, LBC= 3.2 ft, and LcD = 15.0 ft. Determine the magnitude of the maximum bending stress in the beam. P LAB Answer: Omax B LBC ↓↓↓ C ksi W LCD X
Connections Example: Calculate the strength of the single lap joint. The plates are made of 1"x4" wooden blocks with a 2" overlap. The glue can carry 125 psi in shear. The wood can carry an axial stress of 1000 psi. How much force P can the joint carry? Sketch and FBD P b a P
FBD if needed. Kindly skip if not familiar.
Fill in the blanks: The steel rod is stress-free before the axial loads P₁ =169 kN and P2 = 88 kN are applied to the rod. Assuming that the walls are rigid, calculate the axial force in each segment after the loads are applied. Use E-200 GPa. A = 2000 mm² A = 900 mm² A = 1200 mm² P P₂ B C D +250 -350 mm 500 mm A -250 mm- ANSWER: KN, PBC = PCD = KN KN, PAB = (express it in whole number)