3. The manufactures wood beam carries a uniformly distributed load of intensity Wo Determine the largest safe value of w, if the shear stress in the wood is limited to 300psi. 1.0 ft Wo 4 ft- R 0.75 in. 4 in. 1.0 ft 0.75 in. 5 in. 0.75 in. - NA 1=46.7 in.*

3. The manufactures wood beam carries a uniformly distributed load of intensity Wo Determine the largest safe value of w, if the shear stress in the wood is limited to 300psi. 1.0 ft Wo 4 ft- R 0.75 in. 4 in. 1.0 ft 0.75 in. 5 in. 0.75 in. - NA 1=46.7 in.*

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

S9. Knowing that the allowable normal stress for the steel used is 150 MPa, select the most economical metric wide-flange beam to support the loading shown in Figure 9.0. 50 kN/m A D B -2.4 m- 0.8 m 0.8 m Figure 9.0 $10. Determine the average shearing stress in the web of the beam indicated and check whether the design obtained earlier for that beam is acceptable, knowing that the allowable shearing stress for the steel used is 110 MPa. Consider the beam of $9 above.
Note: Read the question carefully and give me both right solutions with clear calculations. Don't copy from already available solutions.
A beam has an f'c = 5000 psi, fy = 60000 psi, reinforcement ratio = 0.0137. Which of the following is most likely true about the strain in the extreme tension steel? Use the tables posted to Canvas as needed (The ones in the back of the book). The strain is = 0.005
A concrete floor slab 100mm thick is cast monolithic with concrete beams 2.0m on centers. The beams have a span of 4.2m, web width of 250 mm and overall depth of 450 mm. The tensile reinforcement consists of 4-25 mm diameter bars in two rows with 25mm vertical clear spacing. Use material strengths f’c = 21 MPa and fy = 415 MPa. Calculate the following considering a T-geometry: Effective flange width of an interior beam in mm = Depth of uniform stress block at ultimate stage in mm to the nearest whole number = Tensile steel strain compatible with concrete strain of 0.003 in 3 decimal places =
The wood beam has an allowable shear stress of tallow = 7 MPa. Determine the maximum shear force V that can be applied to the cross section.
Show complete solution. Thank you
Question 4 A 6 KN force is applied at the free end of a wood (E = 12GPa) beam with dimensions given in Fig. Q4. Neglecting the effect of fillets and stress concentration, determine (a) the maximum compressive stress and its location at section A-A; (b) the maximum shearing stress and its location at section A-A; (c) the deflection at section A-A. 6 kN 300 mm 400 mm ΤΑ 叶 ¡A Fig. Q4 96 mm -- 12 mm 12 mm 48 mm
Use 3 decimal places. Assume that steel yields.
Two pieces of wood, 60 mm by 120 mm each are glued together along the 40° joint. The permissible normal stress in the glue is limited to 100 MPa. The maximum safe load that can be applied at the joint is P+ 40° 60 mm P
1. Figure shows two wood members are joined together using a 60 degrees wood glue adhesive. Find the average normal and shear stress resisted in the plane of the connection. 25 mm 8 kN- 8 kN 60° 30 mm
The two pieces of wood, 2 in. by 4 in., are glued together along the 40o joint. Determine the maximum safe axial load P that can be applied if the shear stress in the glue is limited to 250 psi
Problem 1. The composite beam shown below carries a cantilevered load of 10 kN. The beam consists of one 30 x 124 mm plate and four 12 x 50 mm plates. They are pinned together at 120 mm intervals with round pins. The pin material has a shear strength of 159 MPa. Compute the minimum acceptable diameter for the pins. O O O O O O O -0 O 0- O 1000 mm Do O -120 mm (typ) O O O P = 10 KN 30 x 124 mm 12 x 50 mm (typ)