A 250mm x 600mm 10m-simple spanprestressed concrete beam has a uniformlydistributed dead load of 8.50 kN/m in additionto its weight. The tendons are placed 100mmfrom the bottom of the beam and is subjectedto initial prestress force of 1880 kN. The beamis used to carry a live load of 25 kN/m. If theunit weight of concrete is 24 kN/m3,determine the stress at the bottom fiber ofthe beam at midpan after 20% of the losses atits final stageCS Scanned with CamScanner

Answered: Image /qna-images/answer/f00297b7-634f-4850-a27e-5bbd99ccf4cb.jpg

Answered: determine the stress at the bottom…

Engineering

Civil Engineering

determine the stress at the bottom fiber of the beam at midpan after 20% of the losses at

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Compound axial member ABC has a uniform diameter of d = 1.25 in. • Segment (1) is an aluminum [E1 = 10000 ksi] alloy. The length of segment (1) is L1 = 100 in. %3D Segment (2) is a copper [E2 = 17000 ksi] alloy. The length of segment (2) is L2 = 140 in. %3D When axial force Pis applied, a strain gage attached to copper segment (2) measures a normal strain of ɛ2 = 1500 uin./in. in the longitudinal direction. What is the total elongation of member ABC? L1 P L2 A Aluminum В d Copper c'P Answer: AL = in. %3D
(2) 4 0 5 211 5 4 #9 4 "1 16 #3" ft-k fé = 3 ksi, M = 90 NWC. The section is cracked. Computer the bending stresses in the beam by using transformed-area metho
The brass wire has a triangular cross section, 2mm on a side. The yield stress for brass is Ty= 208 MPa. Gbr= 37 GPa. Determine the maximum torque to which it can be subjected so that the wire will not yield and the angle of twist
need fast
a steel tube sandwiched between two rods, one of aluminum and the other of bronze, and as shown in Fig. 110 - P. The axial loads indicated. Calculate the maximum value of P so that the stress does not exceed in aluminum, MPa 80, in steel 150 MPa, and in bronze 100 MPa.
The rigid bar ABCD supports point loads at A and D and is being supported by two bars at B and C. Determine the absolute value of the deformation at point C. (in mm) 120KN 4m Sm A B L= 6m 9o kN L-4m A= 0.04 m A = 0.0 6m² E=200 GAa E=80 GPa
Problem 1 An axial force of P is applied to the center of the rigid end plate shown below. If the portion of the load carried by the aluminum plates is half the portion of the load carried by the brass core, (a) determine the value of h, (b) the total load if the stress in the brass is 50 MPa. Brass core (E = 105 GPa) Aluminum plates (E = 70 GPa) Rigid end plate 300 mm 60 mim 40 mm
11. Iwo beams, one having square cross section and another circular cross-section, are subjected to the same amount of bending moment. If the cross-sectional area as well as the material of both the beams are same then (A) Maximum bending stress developed in both the beams is the same (B) The circular beam experiences more bending stress than the square one (C) The square beam experiences more bending stress than the circular one (D) As the material is same both the beams will experience same deformation
A steel plate is used to connect a column and beam as shown in Fig. 3. The connection betweenthe beam and the plate is fillet welds. Given Q=150kN and Mx= -5kN-m (applied at centriod ofthe welds between the beam and the plate), determine maximum shear stress in the welds betweenthe beam and the plate.
Compound axial member ABC has a uniform diameter of d = 1.25 in. • Segment (1) is an aluminum [E1 = 10000 ksi] alloy. The length of segment (1) is L1 = 100 in. • Segment (2) is a copper [E2 = 17000 ksi] alloy. The length of segment (2) is L2 = 140 in. When axial force Pis applied, a strain gage attached to copper segment (2) measures a normal strain of ɛ2 = 2300 uin./in. in the longitudinal direction. What is the total elongation of member ABC? L2 (1) Aluminum B (2) Copper Answer: in, AL = i
3) The rigid link is supported by steel wire (1) with an unstretched length of 200 mm and cross-sectional area of 22.5 mm?. Member (2) is a short aluminum of initial length 50 mm and cross-sectional area of 40 mm?. The modulus of elasticity of the steel wire is 200 GPa and the aluminum block is 70 GPa. a) Draw the deflected shape of the rigid member and clearly label the deformation of members (1) and (2). b) Write the equilibrium and compatibility equations needed to solve the problem along with the supporting sketches. Hint: Be sure to carefully consider if the members are elongating or shortening; this must be represented mathematically. c) Calculate the internal forces in both axial members and clearly indicate tension or compression. [Ans. to Check: F2 = 535 N]
Aluminum Bronze Steel 2P 3P P 4P - - 1.0 m 0.8 m FIG. P2.16 2.16 A compound bar consisting of bronze, aluminum, and steel segments is loaded axially as shown in the figure. Determine the maximum allowable value of P if the change in length of the bar is limited to 2 mm and the working stresses pre- scribed in the table are not to be exceeded. A (mm²) E (GPa) G, (MPa) Вronze 450 83 120 Aluminum 600 70 80 Steel 300 200 140