SITUATION 2Determine the safe service load Wpermitted for this beam-column thatis not part of a frame system.Assume ASTM A992 (Fy = 350 MPa;Fu = 450 MPa) as material. Use LRFDspecifications.Servise koadaP= 30 kips dead load80 kips live koadAssumehingedfor bothprincipal10- 0directionsW- 20 dead load8OG live load10-oFined for bothprincipaldirectionsType your final answer/s in the textbox provided below.

Determine the safe service load W permitted for this beam-column that is not part of a frame system. Assume ASTM A992 (Fy 350 MPa; Fu = 450 MPa) as material. Use LRFD specifications. Servise kaad P30kips dead load 80 kips live koad Assume hinged for both principal directions 10-o W- 20 dead load NOG live load AP2

Determine the safe service load W permitted for this beam-column that is not part of a frame system. Assume ASTM A992 (Fy 350 MPa; Fu = 450 MPa) as material. Use LRFD specifications. Servise kaad P30kips dead load 80 kips live koad Assume hinged for both principal directions 10-o W- 20 dead load NOG live load AP2

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Problem 3 The W12 x 53 tension member shown in Figure 5 has two rows of three 25-mm-diameter A325N bolts in each flange. Assuming ASTM A572 (Fy = 345 MPa, Fu = 448 MPa) steel and considering the strength of the W12 x 53 only, a) Determine the LRFD design tension strength ØP of the W12 x 53, b) Determine the service dead load that can be supported if there is no live load, and c) If a service dead load, PDL = 445 kN is applied, what is the maximum service live load, PL, that can be supported?
Check the beam shown in Figure P5.15-4 for compliance with the AISC Specifica- tion. Lateral support is provided only at the ends, and A992 steel is used. The 20-kip service loads are 30% dead load and 70% live load. a. Use LRFD. b. Use ASD. 20k |——3² — 20k FIGURE P5.15-4 W16 x 57 -3'— 3
A built-up section was made using PL414x12mm thk plates as shown in the figure below. It is pinned at both ends with additional support against weak axis at middle point. Assume A50 steel. PL414x12 DO Section W16x67 L x-axis a) Calculate moment of inertia at both axes in mm*. b) Determine the design compressive strength in kN if L-3m. c) Find the design compressive strength in kN if L=18m. Elevation y-axis
130% v - + 7 Annotate T| Edit Trial expired Unlock Full Version ENGR 263 A A A EXERCISES Eleven sets of illustrations and the corresponding free-body diagrams of building-related beams were provided in Chapter 4 as Exercises 4. I through 4.11. These free-body diagrams constitute exercises that will be used here and again in Chapter 12. Follow these instructions carefully to save time later: (a) On each sheet of engineering paper reserved for analysis, calculate the vertical shear specific to that member at appropriate intervals across the length of the free-body diagram. Be sure to solve for locations where shear passes through zero. (b) On cach sheet of engineering paper containing the tree-body diagram, neatly draw the related shear diagram directly below the associated free-body diagram. The shear diagram should be located in the middle one-third of the page. Reserve the bottom one-third of the sheet for the bending moment diagram introduced in Chap- ter 12. Be sure to show…
Problem 3 The W12 x 53 tension member shown in Figure 5 has two rows of three 25-mm-diameter A325N bolts in each flange. Assuming ASTM A572 (Fy=345 MPa, Fu = 448 MPa) steel and considering the strength of the W12 x 53 only, a) Determine the LRFD design tension strength ØP of the W12 x 53, b) Determine the service dead load that can be supported if there is no live load, and c) If a service dead load, PDL= 445 KN is applied, what is the maximum service live load, PL, that can be supported? 5½" OD alb D section b P a. side view Properties of W 12 x 53 Ag 10064.5 mm² d = 307.34 mm b₁ = 254 mm t1 = 14.61 mm E 3" Figure 5 -O O O O b. end view of bolts WT 6 X 26.5 x = 25.9 mm
Q14 What is the available tensile strength of a WT 20x74.5 made of A572 grade 50 steel? Use ASD, assume a shear lag factor (U) of 0.75, the connections are welded, and neglect block shear or other Chapter J requirements. Check both yielding and rupture. a) 800 kips b) 986 kips c) 533kips d) 656 kips
Q9
The truss below is pin connected at A and E, and is acted on by the forces shown. E A D B Identify all of the ZERO-FORCE MEMBERS by checking the boxes below (if there are none, leave all boxes unchecked): BF AF BC BH CD EG -GH AB CH DG DH DE -FH
Select all zero-force members in the truss shown below. Check the box for zero- force members 3 m 3 m 12 m, 8 @ 1.5 m DE O LK ЕР O HF O BC BM EF OM CD BN LO O DK FI O co
A For the truss shown, find veyticat deflection bylunit lead Methed. EA 15 _atfd) Ioku for all members increase in temp is (50€) in (ad) short in (ad)is (3 Emfr
A PL3/8"X6" tension member is welded to a gusset plate as shown in the figure. The steel specification is ASTM A36. Assume that and compute the following: a) The design strength per LRFD b) The design strength per ASD PL ¾ x 6
Please answer