Determine the resulting normal and shear stress components on that plane.

Q: PROBLEM 2: The recangular plate is deformed into the shape of a rhombus shown by the dashed line…

A:

Q: etermine the: 1- Shear

A:

Q: Determine the principal stresses and the absolute maximum shear stress.

A: The stresses are given as, The principal stresses are written as,

Q: Determine the equivalent state of stress on an element at the same point which represents (a) the…

A: The data given is, Normal stress, ?x = -25 Mpa Normal stress, ?y = 0 Shear stress, τxy = 100 MPa…

Q: The bar has a 100 mm by 15 mm rectangular cross section. The allowable normal and shear stresses on…

A:

Q: Determine (a) the principal stresses and (b) the maximum in-plane shear stress and average normal…

A:

Q: The principal stresses at a point across two mutually perpendicular planes are 70 MN/m2 tension and…

A: Mohr's Circle

Q: Determine the principal stresses, the maximum in-plane shear stress, and average normal stress.…

A:

Q: 0 mm A 'B 200 mm, 2 3000 N 12

A: Force = 3000N Cross-section = 12×12mmFind the state of stress at point A and B

Q: 2. determine the maximum normal stress and the maximum shear stress at point O in dia 15 in 3 7 in F…

A: load acting P =15 lbfrom the geometry diameter of the shaft d=0.5"to find (a)  maximum normal…

Q: Determine (a) the principal stresses and (b) the maximum in-plane shear stress and average normal…

A: Given data: The normal stress in x-direction is: σx = -15 ksi (compressive stress is taken as…

Q: Determine the equivalent state of stress on an element at the same point which represents the…

A: According to the given dataWe need to findAverage normal stressMaximum in-plane shear…

Q: Determine the normal stress and shear stress acting on the inclined plane AB. Sketch the result on…

A: Given figure, The normal stress in x direction is €x=500 kpa  Shear stress Txy=0,

Q: The grains of wood in the board make an angle of 20 with the horizontal as shown. Using Mohr's…

A:

Q: The circular punch B exerts a force of P = 1.7 kN on the top of the plate A. (Figure 1) Figure <) 1…

A:

Q: Determine the equivalent state of stress on an element at the same point that represents the maximum…

A: Given: σx=100 kPaσy= 700 kPaτxy=400 kPa To find state of stress on an element at the same point…

Q: Determine the average normal stress at points A, B, and C. The diameter of each segment is indicated…

A: Given data: The diameter of the segment at A, dA = 0.5 in. The diameter of the segment at B, dB = 1…

Q: The grains of wood in the board make an angle of 20° with the horizontal as shown. Determine the…

A: Given data: Axial load acting on the wooden block, P = 250 N. Width of the wooden block, b = 25 mm.…

Q: Determine state of stress at the remaining points (P2, P3 and P4). Calculate the maximum principal…

A: Given: Outer Diameter of the Pole do=115 mm=0.115 m inner Diameter of the Pole di=100 mm=0.1 m To…

Q: Determine the average normal stress developed at points A, B, and C. The diameter of each segment is…

A:

Q: t a point in a strained material the principal stresses are 200 N/mm2 (tensile) and 120 N/mm2…

A: For the solution refer below images.

Q: Determine the principal stresses, the maximum in-plane shear stress, and average normal stress.…

A: Given: The normal stress in the x-direction is бx=30 MPa The normal stress in the y-direction is…

Q: Determine the normal stress and shear stress acting on the inclined plane AB. Solve the problem…

A: Consider the diagram shown in the figure. Here, σx=0, σy=-15ksi, τxy=-6ksi, θ=150°. We need to find…

Q: The plate has a thickness of 20 mm and the force P = 3 kN acts along the centerline of this…

A: Given, thickness of the plate, t=20mm=0.02m Force on the plate, P=3kN We need to Plot the…

Q: The 0.97 in diameter rod is subjected to the loads shown. Determine the normal and shear stress at…

A: To find: The normal and shear stress at point B. Given: The diameter of the rod is d=0.97 in.…

Q: Determine the principal planes and the principal stresses for the state of plane stress resulting…

A:

Q: Determine (a) the principal stresses and (b) the maximum in-plane shear stress and average normal…

A: σx=-30 ksi σy=0Txy=9ksi. To calculate the avg stress σavg=σx+σy2=-30+02=-15ksi Radius of the circle…

Q: Determine the principal stresses and the absolute maximum shear stress.

A: Given dataStress in  y direction σy= 5 ksiStress in z direction σz = -2.5ksiShear stress in yz…

Q: Determine the normal and shear stresses at point D that act perpendicular and parallel,…

A: Given: The load at the point D is 10 kN. The beam is shown below:

Q: The bent shaft is fixed in the wall at A. If a force F is applied at B (the force is acting on the…

A:

Q: Solid shaft AB of the pulley assembly shown in the figure has a diameter of 2.000 in. The length…

A: The tension in the pulley is P=155 lb The length dimensions are a=3 in, b=5.25 in, c=4.25 in The…

Q: Use Mohr’s circle to determine the normal stress and shear stress acting on the inclined plane AB.

A: Given: σx=500 kPaθ=60° clockwise with the given stress. Solution : The plane AB will be 120°…

Q: On the free surface of an aluminum [E = 10500 ksi; v = 0.33] component, the strain rosette shown was…

A:

Q: The state of stress at a point in a member is shown on the rectangular stress element; the…

A: Based on the given diagram,