15 ksi 60° 6 ksi

Q: 5. Determine the normal stress and shear stress acting on the inclined plane AB. Soive the problem…

A:

Q: Oy Txy

A: given; normal stress in x direction =σxnormal stress in y direction =σyshear stress in xy…

Q: he forces applied to pulleys are given as shown below. Accordingly, show the stress state at point A…

A:

Q: The state of stress at a point in a member is shown on the element. Solve the problem using the…

A:

Q: The bar has a 100 mm by 15 mm rectangular cross section. The allowable normal and shear stresses on…

A:

Q: Use Mohr’s circle to determine the principal stresses at the point. Also, find the corresponding…

A:

Q: Determine the principal stresses, the maximum in-plane shear stress, and average normal stress.…

A:

Q: The hook is subjected to the force of 80 lb. Determine the state of stress at point B at section…

A: Given Diameter of the cross-section D=0.5 in. Force subjected on the hook F=80 lb.

Q: Determine the normal stress and shear stress acting on the inclined plane AB. Solve the problem…

A: Given data: Normal stress in y direction, σy = - 15 ksi Normal stress in x direction, σx = 0 Shear…

Q: The stress at a certain point is as shown in the figure. If the maximum in-plane shear stress…

A:

Q: The internal loadings at a section of the beam are shown. Determine the in-plane principal stresses…

A: Given, I section Px =-80 kN = -80 X 103 N My=-500 Nm Mz=10 kNm =10 X 103 Nm

Q: Determine the normal stress and shear stress acting on the inclined plane AB. Sketch the result on…

A: Given figure, The normal stress in x direction is €x=500 kpa  Shear stress Txy=0,

Q: In each case, the state of stress sx, sy, txy produces normal and shear stress components along…

A: (a) sx'=-5 kPasy'=0τx'y'=8 kPau=20°   The stress along the normal -axis:…

Q: At a point in a component, the state of stress is shown on the element below. Assume that the stress…

A:

Q: (          )

A: Tensile normal stresses are considered positive in Mohr’s circle. For the specific stress element…

Q: There is a rectangular plate 2 mm thick on which the forces shown in the figure act. Determine…

A:

Q: The main stress, the maximum shear stress, and the dead angle are obtained when the stress is given…

A:

Q: 60 MPa A 80 MPa 50°

A: The plane on which the value of shear stress is equal to zero is termed the principal plane. The…

Q: Determine the average normal stress at points A, B, and C. The diameter of each segment is indicated…

A: Given data: The diameter of the segment at A, dA = 0.5 in. The diameter of the segment at B, dB = 1…

Q: Determine state of stress at the remaining points (P2, P3 and P4). Calculate the maximum principal…

A: Given: Outer Diameter of the Pole do=115 mm=0.115 m inner Diameter of the Pole di=100 mm=0.1 m To…

Q: Determine the stress components acting on the inclined plane AB in if: normal stressy = 61MPa shear…

A: Consider the following diagram representing stresses acting on the body. The area of cross-section…

Q: Determine the equivalent state of stress on an element at the same point oriented 60°…

A: Given Data: The value of σx=150 MPa The value of σy=100 MPa The value of τxy=75 MPa The orientation…

Q: Determine the principal stresses, the maximum in-plane shear stress, and average normal stress.…

A: Given: The normal stress in the x-direction is бx=30 MPa The normal stress in the y-direction is…

Q: Use Mohrs circle to find the principle stresses and determine the normal and shear stresses acting…

A:

Q: The plate has a thickness of 20 mm and the force P = 3 kN acts along the centerline of this…

A: Given, thickness of the plate, t=20mm=0.02m Force on the plate, P=3kN We need to Plot the…

Q: The horizontal force of P = 80 KN acts at the end of the plate. The plate has a thickness of 10 mm…

A: Given data as per question P = 80KN The thickness of plate =10 mm Area=10×200=2000 mm2 we know…

Q: Determine the shortest distance d to the edge of the plate at which the force P can be applied so…

A: σA=0=σa- σb0 = PA- McI Now Moment of Inertia (I) can be found as follows: I=bd312I=0.01 x…

Q: The box beam is subjected to the 26-kN force that is applied at the center of its width, 75 mm from…

A: Given, P = 26 kN

Q: The bent shaft is fixed in the wall at A. If a force F is applied at B (the force is acting on the…

A:

Q: Use Mohr’s circle to determine the normal stress and shear stress acting on the inclined plane AB.

A: Given: σx=500 kPaθ=60° clockwise with the given stress. Solution : The plane AB will be 120°…

Q: Use Mohr's Circle to determine the maximum shear stress on the element, also using Mohr's Circle…

A: Given state of stress is-To find:The maximum shear stress on the element using Mohr's Circle and The…