The state of stress at a point in a member is shown on the rectangular stress element; the magnitudes of the stresses are |σx|=66 MPa, |σy|=39 MPa|, and |τxy|=71 MPa. Using the stress-transformation equations, determine the state of stress on the inclined plane AB.

Q: бх Oy Txy στ Txy бу In the diagram above, σ = 100 MPa, σy = -27 MPa,, and Tzy = 40 MPa. Let each…

A:

Q: 100 MPa 75 MPa 150 MPa

A:

Q: Determine the principal stresses and the absolute maximum shear stress.

A: The stresses are given as, The principal stresses are written as,

Q: The rectangular bar is connected to the support bracket with a 26-mm-diameter pin. The bar width is…

A: Given data:- Diameter of pin =26mm. The bar width (w)= 60 mm  the bar thickness (t) = 15 mm. Each…

Q: At a point in a stressed body, the cartesian components of stress are sigma xx = 60 MPa, sigma yy=…

A:

Q: 2. determine the maximum normal stress and the maximum shear stress at point O in dia 15 in 3 7 in F…

A: load acting P =15 lbfrom the geometry diameter of the shaft d=0.5"to find (a)  maximum normal…

Q: The state of stress at a point in a member is shown on the rectangular stress element where the…

A: The state of stress at a point in a member is shown on the rectangular stress element where the…

Q: Calculate the normal stresses (in Pa) at point A of the bracket caused by the 11023 N force. E4.png…

A:

Q: For the plane-stress condition given below: σx = 400 MPa σy = 500 MPa τxy = - 30 MPa Construct a…

A: Given: σx = 400 MPa σy = 500 MPa τxy = - 30 MPa To find: Principle stress and the orientation…

Q: The state of plane stress at a point is shown on the element in Figure below. Represent this state…

A: Given: The orientation of element, θ = 45° The stress along x-axis, σx = -10 ksi The stress along…

Q: For the given state of stress, determine the normal and shearing stresses exerted on the oblique…

A:

Q: The strain rosette shown was used to obtain normal strain data at a point on the free surface of a…

A:

Q: The tube has an inner diameter d; = 20 mm and an outer diameter d, = 22 mm. It is subjected to an…

A: In strength of material , Properties and failure of material is analyzed. Material is failed due to…

Q: Determine the average normal stress developed at points A, B, and C. The diameter of each segment is…

A:

Q: The masonry pier is subjected to the FFF = 810 kNkN load. Consider xx = 0.25 mm and yy = 0.5 mm.…

A:

Q: For the shaft shown below, determine the normal and shear stresses acting on the element located at…

A: To find: The normal shear stress acting on the element located at point A, draw stress element at A,…

Q: The plate has a thickness of 20 mm and the force P = 3 kN acts along the centerline of this…

A: Given, thickness of the plate, t=20mm=0.02m Force on the plate, P=3kN We need to Plot the…

Q: A stress element in a rock mass making up a slope experiences a 2D stress as follows: σx = 8 MPa,…

A: given; σx=8MPaσy=4MPaτxy=3MPa

Q: Four stress elements are shown below. All members have the same value for E (Young’s Modulus) and ν…

A: Youngs modulus (E) and poissions ratio (v) are same.And different axial loads are applied for given…

Q: Mohr’s circle is shown for a point in a physical object that is subjected to plane stress. Each grid…

A: Given data as per question Each grid slide=16 MPaFor a point  in a physical object that is subjected…

Q: On the free surface of an aluminum [E = 10500 ksi; v = 0.33] component, the strain rosette shown was…

A:

Stress transformation

The term stress indicates the measure of internal forces that develop due to an external force's application on an object. When a specific external force is applied to an object, internal stress generates in the material. The value of stress can obtain by taking the ratio of the externally applied force and cross-sectional area of the object. There are different types of stress depending on the type of external force.