For the given state of stress, determine the normal and shearing stresses exerted on the oblique face of the shaded triangular element shown. Take X = 45 MPa. What is the normal stress exerted on the oblique face of the shaded triangular element in MPa? What is the shear stress exerted on the oblique face of the shaded triangular element in MPa?

For the given state of stress, determine the normal and shearing stresses exerted on the oblique face of the shaded triangular element shown. Take X = 45 MPa. What is the normal stress exerted on the oblique face of the shaded triangular element in MPa? What is the shear stress exerted on the oblique face of the shaded triangular element in MPa?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine state of stress at the remaining points (P2, P3 and P4). Calculate the maximumprincipal (σ1) and maximum in-plane stress (τmax) for the remaining points (P2, P3 and P4) located at Point A.
Strength of Materials
The question is related to Mohr’s circle and is attached as an image.
Q-2 In an elastic material under load, two planes AB and BC are perpendicular to each other. The stresses on these planes are as follows: 1. on AB, 30 MN/m² compression stress and 60 MN/m² counterclockwise shear. 2. on BC, 60 MN/m² clockwise shear. Find (a) the principal stresses and directions of the principal planes. (b) the normal and tangential stresses on a plane inclined at 75" counterclockwise to the BC plane. Confirm your answer by means of Mohr's stress circle diagram.
For the shaft shown below, determine the normal and shear stresses acting on the element located at point A, including stress concentrations. Then draw the stress element at A with the applied stresses and determine the three principal stress (0₁, 2 and, σ3) using Mohr's circle. r = 0.0042 m, d = 0.03 m, D = 0.033 m, T = 250 Nm P = 1500 N, M = 300 Nm, A M M DEHRƏC T d T P P r
answer this ; The von Mises equivalent stresses at point H can be calculated as MPa
Determine normal stress.
3. Listed below is a combination of stresses acting at a point and referred to axes x and y in an elastic material. Using Mohr’s circle of stress determine the principal stresses at the point and their directions for each combination. 1}sigmax -60 n/mm2 , sigmay -36n/mm2 ,TAUxy=5n/mm2 2}}sigmax 30 n/mm2 , sigmay -50n/mm2, TAUxy= 30n/mm2
Fill in the blanks. Draw and label the Mohr’s circle. For sigma-yp = 30 kSf. does this fail? Find the stresses on the plane shown. Find the plane on which sigma-1 acts relative to the horizontal. Draw them on the figure. Draw the Tresca plot.
The state of plane stress at a point is shown on an infinitesimal element below. Determine the stresses at the point on an element that is oriented 65° counter-clockwise from the x, y axes shown. Enter the shear stress on this rotated element Ta'y' (with correct magnitude and sign) in kPa correct to 3 significant digits below. 300 kPa y 400 kPa X 400 kPa 300 kPa
Determine the principal planes and the principal stresses for the state of plane stress resulting from the superposition of the two states of stress shown. Given: X = 60 MPa and Y = 20 MPa. Determine the orientation of the principal plane in the first and second quadrant. Determine the maximum/minimum principal stresses
The 20 mm diameter rod is subjected to the loads shown.(a) Determine the state of stress at point and show the results on a differential element located at this point.(b) Using Mohr's circle, determine the maximum normal stress and the maximum in-plane shearing stress at point A and show the associated stress states on appropriately oriented elements, for cach case.