Determine the reactive force and moment for the cantilever beam shown below. The beam itself has a mass of 120 kg/m. Note: the pulley is shown diagrammatically but actually has negligible diameter.

Q: inverse kinematics of

A: introduction: we have to find out inverse kinematic

Q: True or False: Holding down the <Shift> key during the CHAMFERcommand allows it to draw fillet…

A: By holding the Shift key before selecting the second object when using a CHAMFER command, the…

Q: ARM processors use instructions to access memory. i. Store ii. Move iii. Load iv. Arithmetic v.…

A: Load and store instructions to access memory in ARM processors. Option A

Q: I need parts 1, 2, and 3, answered pertaining to the print and instructions.

A: (1). The name of the circuit is HYDRAULIC CIRCUIT FOR 90 TON COMPACTION PRESS.

Q: In a CNC feed drive, a stepper motor with step angle of 1.8 degree drives a lead screw with pitch of…

A: Given data  Step angle θ= 1.8°  Pitch P= 2mm

Q: For FANUC 6 axis robot How many E-stop buttons does the Fanuc robot system have? Where are they…

A: E-stop buttons are found in various parts of a system. They are designed to be highly visible and…

Q: (a) The free body diagram of the rudder. (b) If the maximum permissible load that the steel…

A: (a) y5=2xDifferentiating above with respect to x,5y4dy=2dxdx=52y4dy…

Q: For a Fanuc Robot What button on the teach pendant selects the modes such as World and Joint?

A: The FANUC automaton i series could be a series of extremely reliable intelligent robots with the…

Q: I need parts 7, 8, and 9, answered pertaining to the print and instructions.

A: As we are entitled to answer only a single question. We’ll answer question no. 7 for you. Please…

Q: Construct two position synthesis of single slider crank mechanism by relative pole method.

A: introduction; relative pole method- relative pole is the center of its rotation with respect to…

Q: This is an example of Tool offset made in CNC milling O a. 02 O b. H2 O c. TO2 O d. O-02

A: Solution:

Q: Joint 2 Join

A:

Q: 2. A+B=X

A: As per request I am solving part 2.

Q: - 20 cm long ground link - 10 cm long

A: To create a four-bar linkage with an output link that can make complete circles, you can use the…

Q: Draw the top and front view of the figure 2 using AutoCad

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: What is the purpose of a clearance plane in CNC programming and milling?

A: In CNC programming and machining, a safety zone of 0.050" or 0.100" above the workpiece or work…

Q: Q2. Draw a quick return mechanism that has time ratio between return and forward of 4:7.

A: Given:The quick return ratio or time ratio of the forward stock to return stock is   where the…

Q: Define the function of the rocker arm in the figure.

A: Given figure : TRANSLATORY HYDRAULIC DRIVE  FIGURE :

Q: how to calcuate moment for ridig body

A: The moment or torque of a force about a point or an axis is a measure of the tendency of rotation.

Q: (MO14) 4. Design a quick return mechanism with 270 cm stroke, time ratio of 3, fixed link length of…

A: Consider the given data, Crank length, s= 97.5cm Time ratio, t=3 Fixed link length, l=75cm Stroke,…

Q: a) Assign the frames, and derive the link parameters in the DH table. b) Calculate the forward…

A:

Q: explain the Frank-Read source multiplication mechanism

A: The frank read source is a mechanism based on dislocation multiplicationin a slip plane under shear…

Q: Put in ternary links without changing its mobility. Sketch linkage.

A: Given drawing of the ternary link mechanism or  four bar mechanism

Q: hy is incremental positioning usually used with an axis return?

A: The absolute coordinates system the reference each position on the work piece is same or origin…

Q: QUESTION 4 A subset of the previous mode, VQC contains the stored codes for using the and tool…

A: Visual Quick Code is a template-driven conversational programming system that makes creating simple…

Q: draw the Bode diagram

A: Given:

Q: /5 --- A computer cannot "boot" if it does not have the

A: An operating system is the system software that handles the software and hardware resources and…

Q: How to perform zero point reset

A: Zero point reset is an introducing system for tenant discovery sensor that should be performed…

Q: Interpolator in

A: Interpolator in a CNC machine.

Q: Which of the following is true about machine home, part origin, and tool change position? (choose…

A: option  b and c is correct  part origin is set by the programmer. all subsequent relative programmed…

Q: As mentioned in the below given DCV, extend stroke respectively. and Lare the positions are used for…

A:

Q: Describe the manipulator (joints, degrees of freedom, sketch the end effector workspace).

A: In the given figure there are three links in the mechanism, in which one link is a fix link and…

Q: Which command is not modal?

A: All are modal for G code.

Q: What three simultaneous conditions must be satisfied for SCC?

A: SCC requires three conditions to be satisfied simultaneously:           1) a tensile stress above…

Q: True or False: You can only use the REDO command immediately after using the UNDO command.

A: The UNDO command takes back the work in a drawing session whereas the REDO command will take the…

Bending Moment

In general, we can define the bending moment as the reaction induced when a certain amount of load or force is applied to an element which makes it bend.