For a Fanuc Robot What button on the teach pendant selects the modes such as World and Joint?

Q: 2. Determine the clamping force on the bolt and reactions at pin A for the pliers shown.

A: It is required to determine the force on the bolt and reactions at pin A, given that the applied…

Q: In the diagram the ring is pulled down by two forces F and F2 to create a resultant force F, having…

A: a) The FBD of the figure is given below -

Q: If your home (in CA) requires 1.5 million Btu of heat energy from the furnace on a cold winter day,…

A: The volume of Natural Gas required is to be determined from which price needs to be obtained

Q: For FANUC 6 axis robot How many E-stop buttons does the Fanuc robot system have? Where are they…

A: E-stop buttons are found in various parts of a system. They are designed to be highly visible and…

Q: What does the schematic symbol below representing?

A:

Q: Part A The force F = (-6i+ 3j+ 14 k) N is applied to the block shown in (Eigure 1). Figure -3 m 2 D…

A:

Q: Problem-5. For the systems given below, where the input is unit step function, (a) Obtain the time…

A: c1(s)R(s)=5(s+3)s2+8s+15=5(s+3)s2+(2×4s)+16-1=5(s+3)(s+4)2-1  for (s+4)2=1, s=3,5therefore…

Q: What criteria does the linker use to choose between these two seemingly equivalent operations?

A: Equivalent operations produce the same result but can use different methods or syntax. In…

Q: Write and draw the following grashof's criterion and kind of grashof's four-bar mechanism such as;…

A:

Q: 1. The precision of CNC system depends on used by the controller to the ... ... define the axis…

A: This question is from production engineering.

Q: An emergency stop system is to be designed for a certain automatic production machine. A single…

A: Understand that the machine is started with a single start button X1 which is normally open switch…

Q: For the situation shown in Fig. below calculate, centerline and surface heat rate per unit of…

A: AS WE CANNOT PROVIDING THE HAND WRITTEN SOLUTION SO I AM TYPING IT  FOR YOU Given Data- Radius…

Q: what type of CNC programming command sets the machine into a certain mode, which stays active beyond…

A: there are two type of CNC  command sets, 1).Modal:-in this set of command vommand are effective…

Q: 1. Hello can you find Ir1,ir2 ,Ireland, rt and it and pt. Thank you please show me how to do my…

A: Draw the circuit using the directions of currents in each resistors.

Q: FOR A FANUC 6axis robot What button on the teach pendant is used to select a program?

A: What button on the teach pendant is used to select a program?

Q: Can someone draw grashof's mechanism: Crank-rocker Mechanism in ENGINEERING DRAWING FORMAT basing…

A: The crank-rocker mechanism,

Q: Produce a 3D solid model of the Guard casing and test boss and produce an assembly of the two parts…

A: Given Guard casing Test boss To find Parts Assembly

Q: How many DOF do the following have in their normal environment ? a. submerged submarine b. An…

A: DOF stands for the degree of freedom which indicates the number of values that can be changed…

Q: Define an Articulated Robot?  How many joints does a 6-axis Articulated Robot have?  How many joints…

A: Note: As per our company guidelines we can answer up to 3 sub-parts. I am answering first 3…

Q: Describe the manipulator (joints, degrees of freedom, sketch the end effector workspace).

A: In the given figure there are three links in the mechanism, in which one link is a fix link and…

Q: For a FANCU Robot What position should the Teach pendant Enable/Disable switch be in for manual…

A: The FANUC automaton i series could be a series of extremely reliable intelligent robots with the…

Q: What three simultaneous conditions must be satisfied for SCC?

A: SCC requires three conditions to be satisfied simultaneously:           1) a tensile stress above…

Q: True or False: You can only use the REDO command immediately after using the UNDO command.

A: The UNDO command takes back the work in a drawing session whereas the REDO command will take the…

Q: an automatic door mechanism where when a specific sensor on top detects a user approaching, where…

A: Draw the flow chart.

Q: Discussion object are the same? 2- When and why will the floating object become unstable?

A: This question is based on the topic of fluid mechanics in which it discusses about stability of…

Q: How many possible gaits (distinct combinations of lift/release events) can a 4 legged robot like the…

A: Given:- 4 legged robot To find:- Possible gaits

Q: e 3 al Views xiliary View 75 TOP VIEW 1₂ 26 26 PLAT SLOTTED SCALE

A: GIven

Q: Two objects (m₁ = 5.05 kg and m₂ = 3.50 kg) are connected by a light string passing over a light,…

A: Given data: m1=5.05 kgm2=3.5 kgh=4 m Need to determine the speed of each block when they passes to…

Q: Bohar model Gizmo answer keys

A: Niels Bohr proposed in 1913 that the unique spectral lines produced by various elements were related…

Q: B. Material Holder Bending Arm A Stop End Material Bending Die

A:

Q: Mechanical Draw the part Niew shown ASing object snap moc drawing as P7-1. ave the 04.50 3X 02.00

A: object snap use to get precise location of particular points on object like tangent on circle at…

Q: w can move drone in hexacopter from one side to another side??

A: given: how can move drone in hexacopter from one side to another side??

Q: In a certain industrial process, oil of density p flows through the inclined pipe in the figure…

A: Here, the given pipe flow is steady , U tube manometer is connected between section (1) and (2) .The…

Q: FOR A FANUC 6 axis robot What is the purpose of the Deadman’s switch?

A: 1.The FANUC S-6 is a six-axis, standard construction, electrical servo-driven mechanism that has…

Automation in manufacturing processes

The term automation refers to the technique through which the creation of an apparatus takes place using an automatic process or a system. Let us try to understand this with an example.