Determine the rate of flow of water through a pipe of diameter 20 cm and length 50 m when one end of the pipe is connected to a tank and other end of pipe is open to the atmosphere. The pipe is horizontal and the height of water in the tank is 4m above the centre of the pipe. Neglect the minor losses and take f = 0.009.

Determine the rate of flow of water through a pipe of diameter 20 cm and length 50 m when one end of the pipe is connected to a tank and other end of pipe is open to the atmosphere. The pipe is horizontal and the height of water in the tank is 4m above the centre of the pipe. Neglect the minor losses and take f = 0.009.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Water flows steadily into the Venturi tube in the following figure. In the section considered, negligible friction losses and uniform properties in the sections are assumed. The entrance area (A1) is 20 cm2, while the throat area is A2 = 10 cm2. A pressure gauge whose manometric fluid is mercury (Yhg = 136,000 N / m3) is connected between the inlet sections and the throat, as seen in the figure. The flow of water that flows through the Venturi tube is requested (γH2O = 10,000 N / m3. Answer .: ϕ = 5.8 L / s.
An engineer must design the support system to hold the pipe junction. Determine the reactions to design this system. The system into the discharges (15%) atmosphere. V2=7m/s 45° V1=16m/s 18 cm 4D1-> P=60 kPa 20 cm V3-33 m/s
Consider the flow of water through a pipe with a constant area in a vertical plane. What is the relation between the static pressures at 1 and 2? Assume no losses. g None of the above P1P2
4. Two reservoirs, A and B, are connected by a pipeline which is 1300 m long. The surface of reservoir B is 10 m lower than that of reservoir A. There is a small hill between the two reservoirs with the highest point at 500 m along the pipe from A. If the pipeline has a diameter of 300 mm and a friction factor of λ = 0.008 then determine the following: (Ignore the minor losses and assume that the pipe is already flowing full and at a steady flow) (a) The flow in the pipe (b) If the lowest permissible absolute pressure head in the pipeline is 2.5 m of water, determine how high above reservoir A surface level the pipe can be laid so that the minimum pressure condition is satisfied. (Assume atmospheric pressure of 105 Pa.)
A vertical pipe of 1 m diameter and 14 m length has a pressure head of 5 m of oil at the upper end. When oil flows through the pipe at an average velocity of 4.5 m/s, the head loss due to friction is 1.8 m of oil. The density of oil is 840 kg/m3 Find the pressure at the lower end of the pipe, when the oil flow is (a) ) Pressure at lower end when flow of oil upward direction (b) ) Pressure at lower end when flow of oil downward and also draw the neat sketch.
Water is pumped from a lake to a reservoir at 0.021 m^3/s. The pump has a horsepower of 13 and an efficiency of 40%. There is a 12 foot elevation from the lake to the reservoir. Determine the mechanical power needed to pump the water up the reservoir in W.
The pumper truck shown in the figure below is to deliver 1.4 ft3/s to a maximum elevation h of 58 ft above the hydrant. The pressure at the 4-in.-diameter outlet of the hydrant is p-11 psi. If head losses are negligibly small, determine the power that the pump must add to the water. Assume D-4 in. W shall Hydrant hp
A large, open-topped water tank is being filled from above by a 1.0-cm-diameter hose. The water in the hose has a uniform speed of 11 cm/s. Meanwhile, the tank springs a leak at the bottom. The hole has a diameter of 0.70 cm. Determine the equilibrium level heq of the water in the tank, O measured relative to the bottom, if water continues flowing into the tank at the same rate. heq 1.26 X10-3 Incorrect m
Water at 15 degrees Celsius is flowing through a 2-in ID smooth pipe. The friction loss for a 100-ft section of the pipe amounts to 4.8 lbf/lbm. Determine the velocity of the flow.
Oil with specific gravity of 0.87 is being pumped from a reservoir to an elevated tank as shown below. The pump in the system is 80% efficient and is rated at 240 kW (i.e. Pp is 240 kW). Determine the flow rate of oil in the pipe if the total head loss from point 1 to point 2 is 12 m of oil. Point 2 represents the exit of the pipe. Reference line is the ground level. The stopping error ɛs is 3%. You should maximum have 2 iterations after the first value. Elev. 2 50 200-mm-diameter pipe Pump -160-mm -diameter pipe -Elev. 150 m Oil
Water flows through a corner valve at a flow rate of Q=0.75 m³/s . The pressure just upstream of the valve is P₁ = 500 kPa and the pressure just downstream is P₂ = 300 kPa. The inside pipe diameters of the valve inlet and exit are respectively, D₁ = 5 cm and D₂ = 12 cm. If the flow through the valve occurs in a horizontal plane, determine the head loss, h₂ (in meters) and the rate of loss of available energy (in W) across the valve. D2 Di
The diameter of the smooth pipes used in the pumping system in the lower figure is 150 mm and its total length is 80 m. In this system, there are four elbows with a loss coefficient of 0.2. It's lost its coefficients are 0.5 for the inlet to the pipe, 0.7 for the valve and 1 for the inlet to the tank. z2-z1=15 m, above manometric pressure if the flow of water pumped into the tank is 50 L/s and the overall efficiency of the pump is %84 find his height and strength. Take the viscosity of water is 0.001 kg / m.s