Determine the positive moment in the direction of the short side for deck 6. Take the design load to be 9.5 kPa, the beams to be 35x75 cm, and the columns to be 55x55 cm. Consider that the casting is monolithic

Determine the positive moment in the direction of the short side for deck 6. Take the design load to be 9.5 kPa, the beams to be 35x75 cm, and the columns to be 55x55 cm. Consider that the casting is monolithic

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

4 Two plates (14 in x 2 in) are welded to an I-beam (W12 x 16). Find the moment of inertia with respect to the x-axis. x-axis__ I anial
Q6b .solve this.
18. A steel loop ABCD of length 1.2 m and of 10-mm diameter is placed as shown around a 24 mm diameter aluminum rod AC. Cables BE and DF, each of 12 mm diameter, are used to apply the load P. Knowing that the ultimate strength of the steel used for the loop and the cables is 400 MPa and that the ultimate strength of the aluminum used for the rod is 220 MPa, determine the largest load P that can be applied if an overall factor of safety of 3 is desired. a. 37.7 KN b. 39.7 KN E С. 74.6 KN d. 45.2 KN B 180 mm 480 mm A 180 mm D
1-7. Determine the resultant internal loading on the cross section through point D of the pliers. There is a pin at A, and the jaws at B are smooth. 20 N 20 N -120 mm- 80 mm 30° 40 mm 15 mm B
In the assembly shown. the block has a weight w = 200 lbs and the cord is attached to the pin at B. The pulleys have radi of rt = 2 Tn. and r2 1 În. Neglect the mass of the pulleys and the link. Pulley Pulley A 45 12 Compute the reaction at the ĩnk AB In lbs." 250 260 280 B.
ANSWER ONLY AC BC CDwrong answer gets downvote so double check the answer cause it will be input in the system
F1 Determine the reaction forces for girder G-1. Column A Beam B-1 L1 -0 Beam B-2 F2 Girder G-1 Please round to the nearest one. Reaction force for Girder G-1 (Column A side) = Girder G-2 L1 After the initial calculation, we determined the following information: • The reaction force for Beam B-2 (Girder G-1 side) = 17,890 lbs • The reaction force for Beam B-3 (Girder G-1 side) = 15,685 lbs Reaction force for Girder G-1 (Column B side) = 80 F3 • Live load 50 psf • Dead load: (1) Slab = 50 psf, (2) Deck = 10 psf, (3) Mechanical equipment = 8 psf, (4) Suspended ceiling = 8 psf (5) Beam = 25 lb/ft, (6) Girder = 35 lb/ft • Beam and Girder spacing:: (1) L1 = 14 ft, (2) L2 = 10 ft, (3) L3 = 10 ft Beam B-3 000 000 F4 lbs open lbs F5 L1 Column B Beam B-4 L2 F6 L3 MacBook Air ← F7 F8
8m A 6M using in F B с 100KN 8m 6m Method of Sections determine forces FE, FC, BC
Which of the following statements is correct about the given structure? A В C E pin fixed roller fixed It is a determinate structure. O It is indeterminate to 4 degrees. It is indeterminate to 5 degrees. O It is indeterminate to 3 degrees .
2. The lap joint is fastened with four 30-mm-diameter rivets. The working stresses are 84 MPa for the rivets in shear and 84 MPa for the plates in bearing. Find the maximum safe axial load P that can be applied to the joint. Assume that the load is equally distributed among the rivets... 35 mm KATIN 160 mm
What is the normal force at point A and the reaction at point B given thr static friction of 0.85?
Aload Pissupported by a structure consisting of rigid bar ABC, two identical solid bronze [E = 17400 ksi] rods, and a solid steel [E = 30600 ksi] rod, as shown. The bronze rods (1) each have a diameter of 0.79 in. and they are symmetrically positioned relative to the center rod (2) and the applied load P. Steel rod (2) has a diameter of 0.52 in. Assume L1=39 in and L2=77 in. If all bars are unstressed before the load Pis applied, determine the normal stresses in bronze rods (1) and steel rod (2) after a load of P = 29 kips is applied. |(2) (1) L2 (1) B. Answers: i ksi. ksi.