A built-up section is made from 450mm x 20mm as flanges and 500mm x 20mm as web asshown. All plates are A50 steel and the flanges are continuously connected to the web by means ofweld. This section will be used as a beam to support a factored distributed load as shown.450mm x 20mm50 KN/m5.0m3.0m450mm x 20mmA. Determine the moment of inertia along the neutral axis.B. Determine the shear flow at the neutral axis.C. Determine the shear strength capacity and adequacy of the built-up section using LRFD-NSCP2015 provisions.500mm x20mm

Answer (A) Calculation of Moment of inertia along the Neutral axis Since the section is…

A built-up section is made from 450mm x 20mm as flanges and 500mm x 20mm as web as shown. All plates are A50 steel and the flanges are continuously connected to the web by means of weld. This section will be used as a beam to support a factored distributed load as shown.

A built-up section is made from 450mm x 20mm as flanges and 500mm x 20mm as web as shown. All plates are A50 steel and the flanges are continuously connected to the web by means of weld. This section will be used as a beam to support a factored distributed load as shown.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 1. The figure shows a roof truss and the detail of the connection at joint D. Member DE is angle…

Q: The member is connected to a gusset plate with 10 inch longitudinal welds. Fin el shape to carry the…

Q: Determine the maximum load P that can be applied to the lap joint connected by three – 16 mm…

A: STEEL STRUCTURES:

Q: ACTIVITY The figure shows a roof truss and the detail of the connection at joint B. Members BC and…

Q: 2. A vertical member of a steel truss is subjected to a live load of 25 kN and a service dead load…

A: Solution: Given: LL = 25 kN DL = 50 kN U = 1.0 Plate dimensions: 10 x 100 mm Factored load: P = 1.2…

Q: Solve for the forces at all members of the truss shown below. Identify if the member is in tension…

A: Solution: Using equilibrium condition: ΣFx=0Ax=280 kNΣFy=0Ay+Gy-150-150=0Ay+Gy=300 Taking moment at…

Q: : For the truss systems shown below: • Identify zero force members. • Identify members in tension,…

Q: Problem 912 Compute the stresses at A and B on the link loaded as shown in Figure P-912 if P = 9000…

A: a ) P = 9000 lb and F = 3000 lb Compute the stresses at A and B ? Solid mechanics problem.

Q: 2. A vertical member of a steel truss is subjected to a live load of 25 kN and a service dead load…

A: LL = 25 kNDL = 50 kNU = 1.0Plate dimensions: 10 x 100 mmFactored load:P = 1.2 DL + 1.6 LL = (1.2x50)…

Q: 143. Which of the following is not a built-up shape? Double angles c. Plate girders d. Unequal leg…

A: 143. Built-up section are the sections made by joining two or more hot rolled sections. Double…

Q: 5/8 in- diameter steel rod AB is fitted to a round hole near end C of the wooden member CD. For the…

A: This question is related to the Bending Stresses from Strength of Material. In this question we…

Q: A flexural member is fabricated from two flanges plates 1" x 20" and a web plate 1/2" x 22". The…

Q: The value (U) in (AISC) for welded member in tension load, if (2w > L>= 1.5w) where L: length of…

A: Given data Welded member Length of weld Distance between welds

Q: allowable

A: Block shear strength Agv =12in2×4 in= 4.00 in2Agv = 4.00 in2Ant = 12in10in = 5.0 in2Ubs = 1.0Rn…

Q: Apply AISC LRFD procedure to design a welded connection for a vertical truss member L127x76x9.5 with…

Q: In the steel structure shown a 6 mm diameter pin is used at C and 10 mm diameter pin is used at B.…

A: Given:Diameter of pin at C is 6mmDiameter of pin at B is 10 mmRequired:Largest P applied

Q: Solve a 100 x 100 x 10mm angle is to be welded to a gusset plate shown. The angle carries a load of…

A: Given strength of fillet weld 94 mpa Size of fillet weld = 8 mpa Load to be carried = 185 kn

Q: THIS IS NOT A GRADED ACTIVITY. THIS IS JUST A REVIEWER FOR MY TRUSS DESIGN. THANK YOU SO MUCH!…

Q: Consider the truss shown. Determine the force acting on member CF, EF, and FG. B A D 3 m E 4 m 45 kN…

Q: X1=2 X2=802 2- A 530*150 is used as a compression member with one end fixed and the other end free.…

A: The given data is: E=2*105 MPa Ag=19200 mm2 Fy=350 MPa ry=73.4 mm L=3200 mm K=2.1 as one end is…

Q: In a truss girder of a bridge, a diagonal consists of mild steel flat 400 I.S.F. and carries a pull…

A: Truss girder A girder truss spans a roof or other structure and is designed to carry a greater load…

Q: A tension plate shown below is used to support suspended load "T". Gusset Plate Fy = 248 MPa Fu =…

Q: Calculate the maximum shear force in the welds in the given figure. P=160KN X = 150mm y= 125mm…

Q: dentiry the shown. (Enter your separated E A

Q: 3 A plate is connected to the flange of an ISMB as shown. The factored load is 100 kN. Find the size…

Q: Six rivets are used in the connection shown in the figure. If both P=50kN, what is the minimum…

Q: What is the required diameter of sag rods in mm? Considering sag rods and tie rods at midspan…

Q: Determine the force in each member of the truss shown. Indicate whether the members are in tension…

Q: 4. Six rivets are used in the connection shown in the figure. If both P = 50 kN, what is the minimum…

A: Load P = 50KN Allowable shear stress = 70MPa Bearing stress = 40MPa

Q: Beam AB is supported as shown in Figure. Tie rod (1) is attached at B and C which are double-shear…

A: Data Given: w = 1800 lb/ft σs = 54 ksia = 15 ftb = 30 in.c = 7 ft.fy = 36 ksiFOS = 2.5 Asked:…

Q: Determine the resultant load on the most stressed bolt in the eccentrically loaded connections…

A: Consider the free body diagram;

Q: The figure shows a roof truss and the detail of the connection at joint D. Member DE is angle…

Q: Give the formula for the tensile and shear strength of the weld joint. Explain the various terms in…

A: Need to definethe formula for the tensile and shear strength of the weld joint

Q: Determine the maximum service load, P, that can be applied if the live load-to-dead load ratio is…

A: Solution:

Q: Example: Calculate the strength of the single lap joint. The plates are made of 1"x4" wooden blocks…

Q: A structural tee bracket is attached to a column flange with six bolts as shown in Figure . All…

A: Solution

Q: A flexural member is fabricated from two flange plates 1/2in x 16in and a web plate 1/4in x 20in.…

Question

A built-up section is made from 450mm x 20mm as flanges and 500mm x 20mm as web as
shown. All plates are A50 steel and the flanges are continuously connected to the web by means of
weld. This section will be used as a beam to support a factored distributed load as shown.
450mm x 20mm
50 KN/m
5.0m
3.0m
450mm x 20mm
A. Determine the moment of inertia along the neutral axis.
B. Determine the shear flow at the neutral axis.
C. Determine the shear strength capacity and adequacy of the built-up section using LRFD-NSCP
2015 provisions.
500mm x20mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Name: Time you spent to solve the problem HW- 3 ID.: 'Dėtërminë thé forċés in all the members, and state if these memibers are in tension or compression. Use table to arrange your Cal&tlations, show the results on the truss ( if not your witf täke zerở)** 30 N 4m 3 т 15
By inspection, determine the zero-force members in each truss. Identify the zero-force member by placing an “X” through that member. If you need to do this iteratively, and redraw the truss without the zero-force members you have already found, you may do so.
Please solve for the value of P.
?
STEEL STRUCTURES
The allowable unit stress in shear on a fillet weld is 13,600 psi, and the total actual length of the weld CANNOT exceed 3 in. If the weld must transmit a total force equal to 9600 lb. Its size should be A. 1/2 in B. 3/8 in C. 5/16 in D. 1/4 in
please show all work, thank you!
WT12 x 38 Longitudinal welds Given: Properties of WT12 x 38: A, = 11.2 in? y = 3.0 in. b = 8.99in. Use A992 Steel: F, = 50 ksi F = 65 ksi LL = 3 DL %3D %3D tw = centroidal distance bf A. Governing Ultimate Tensile Capacity based on Yielding of gross section Round your answer to 0 decimal places.
Please help me. I'll give a thumbs up
Design the reinforcements of the given T beam below. bf=800mm bw=450mm tf=120mm d=600mm d'=80mm fc'=35MPa fy=350MPa USE NSCP 2015 A.Mu = 1300kN-m, As = B.Mu = 1600kN-m, As = mm2 _mm2, As' = mm2
A tension plate shown below is used to support suspended load "T". Gusset Plate- F, = 248 MPa Fu = 400 MPa %3D 200 mm a) Determine the allowable tensile capacity of the plate if L= 240 mm. (Assume weld strength is satisfactory).
I need the answer as soon as possible