Determine the output voltage of the first stage of this amplifher in terms of v1. ( Select ) Determine the output voltage of the 2nd stage in terms of vo1 (output of 1st stage) and v2. ( Select ] Determine the final output voltage in terms of v1 and v2. ( Select) VI w 1.0V 1ka 4kQ A35.0V 741 1kQ 1kQ 9-35.0V 142.90 35.0V 741 35.0V

Q: nsider the following PLA connection diagram. The PLA table contains the entry B D F1 F2 F3 a.…

A: Solution-From the given PLA connection diagram, the operations for F1, F2 and F3 are given as,F1=…

Q: QUESTION 13 L1 Inputs o-S1 0-S2 0-53 0-S4 0-S5 0-S6 0-S7 -S8 o-Se oaS10 8 oo-S11 o-S12 0-S13 10 11…

A: The given ladder logic diagram is shown below. It is mentioned to assume all switches are turned…

Q: Q2. The single-line diagram of a simple three-bi is shown in Figure-2. Each generator is repres-…

A: the single line diagram of a simple three bus power system is shown. Each generator represent by an…

Q: In the circuit below, assume that the current directions are as shown. Also, traverse the loops in…

A: We know that the current flows from positive polarity to negative polarity through a resistor. Using…

Q: 5. In the figure, E₁ = 6.00 V. E= 12.0 V, R₁ = 100 S2, R₂ = 200 52, and R₁ = 300 2. What are the…

A: here we have to find the size and direction of currents through the resistors R1 , R2 , R3 .

Q: Which of the following statements is correct for any closed loop system? a) Only one of the static…

A: Type of control system Closed-loop control system  The more accurate response even in the case on…

Q: Point charges Q₁ = 1 nC, Q₂ = −2 nC, Q3 = 3 nC, and Q4 = −4 nC are posi- tioned one at a time and in…

A:

Q: Using GG  for positive counters and RR  for negative counters, perform the addition problem with…

A: Given, GG  for positive counters and RR  for negative counters. Perform using counters: -4 ++ 7

Q: 6. Given the ripple adder circuit provided in Figure 8-2 (below) and the following inputs, a3 ao…

A: The ripple adder is a combination of four Full adders connected in cascade to compute 4-bit…

Q: What exactly is a load balancer? What is the purpose of a load balancing device?

A:

Q: (2) Use The current used for a No-Load condition is Partial Load. The current for used for a Full…

A: Current drawn by the machine during no load condition is minimum (nearer to zero). Hence, the…

Q: Problem #21) Determine the source current Ipc and the resistor voltage V4 as shown in the following…

A:

Q: (II) Explain what happens if the topology is modified as shown in figure below. VREFO- ww Qz

A: According to questions we need explain about the given modified circuit.

Q: Using Multisim please

A: The objective of this question is to design a traffic control system for a four-way intersection…

Q: What is matching impedance? What does short circuit with matching impedance mean?

A: Solution: Impedance is a measure of the opposition that a circuit or device offers to the flow of an…

Q: Two 36 cell PV modules are connected in series. One is shaded and the other is fully illuminated,…

A:

Q: Please write equations for both the pull up and pull down of the complex gate. Note: these are not…

A: The equations are

Load flow analysis

Load flow analysis is a study or numerical calculation of the power flow of power in steady-state conditions in any electrical system. It is used to determine the flow of power (real and reactive), voltage, or current in a system under any load conditions. 

Nodal Matrix

The nodal matrix or simply known as admittance matrix, generally in engineering term it is called Y Matrix or Y bus, since it involve matrices so it is also referred as a n into n order matrix that represents a power system with n number of buses. It shows the buses' nodal admittance in a power system. The Y matrix is rather sparse in actual systems with thousands of buses. In the power system the transmission cables connect each bus to only a few other buses. Also the important data that one needs for have a power flow study is the Y Matrix.

Types of Buses

A bus is a type of system of communication that transfers data between the components inside a computer or between two or more computers. With multiple hardware connections, the earlier buses were parallel electrical wires but the term "bus" is now used for any type of physical arrangement which provides the same type of logical functions similar to the parallel electrical bus. Both parallel and bit connections are used by modern buses. They can be wired either electrical parallel or daisy chain topology or are connected by hubs which are switched same as in the case of Universal Serial Bus or USB.