Determine the net area of the given section below. Diameter of bolts is 7/8-in and the thickness of the plate is 3/8", in in. The channel used is C8x15 and the plate in between the channels are 10" in width. Select one: a. 6.69 b. 3.43 c. 5.75 d. 2.25

Determine the net area of the given section below. Diameter of bolts is 7/8-in and the thickness of the plate is 3/8", in in. The channel used is C8x15 and the plate in between the channels are 10" in width. Select one: a. 6.69 b. 3.43 c. 5.75 d. 2.25

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The tension member shown contains holes for M20 bolts. At what spacing (mm), s, will the net area…

Q: snip

A: Calculate the gross area due to yielding. Ag=bt =5×12 =2.5 in2 Calculate the nominal…

Q: 8. For the two lines of holes shown in the figure below, determine the pitch that will give a net…

A: Given data in question Hole diameter 19 mm Width 150 mm To find out Pitch

Q: Determine the design strength of a single C15x50 fastened to a 3/4" gusset plate. Use A36 steel.…

Q: For the A36 beam shown in the accompanying illustration, what is the required spacing of 7/8-in A307…

A: Consider the free body diagram;

Q: The tension member shown contains holes for M20 bolts. At what spacing (mm), s, will the net area…

Q: Example 3.9 FIGURE 3.20 Find the available strength of the S-shape shown in Figure 3.20. The holes…

A: Given member: S15×50 Properties of the given section: Flange thickness=0.622 in We need to…

Q: The tension member shown contains holes for M22 bolts. At what spacing (mm), s, will the net area…

Q: Q17 An L4x4x7/16 tension member is connected with %"Ø bolts, as shown in the figure below. Both legs…

A: Given Data: The size of the tension member is L4×4×716. The diameter of the bolt is 34". To…

Q: discuss the possible failure modes when in different bolts when the bolts are subjected to shear,…

A: Possible Failure Modes of Bolts in Shear, Tension, and Combined LoadingBolts are critical components…

Q: Angle Bolted Connection. The L6 x 31/2 × 5/16. -in angles, shown in Figure, The bolts are 3/4 inch…

Q: The design shear strength phi rnv of one A490 X-bolt, 3/4 inch in diameter (Group B, X type) in…

Q: Compute the allowable tensile strength of the bolted connection shown. Include the allowable block…

A: The angle is made of A36 steel and the bolts are 3/4 inAll parameter is given belowNeed to findTo…

Q: Determine the forces that are generated in the bolts (The information is given in units of weight)…

Q: Calculate the critical net area (mm2) for the tension member shown. The pitch and the gage are 50 mm…

Q: ) Determine the smallest net area of the tension member shown. The holes are for 19 mm Ø bolts at…

Q: Compute the net area. The 1 x 10 plate shown in Fig. P3-10.The holes are for 7/8-in Ø bolts.

A: The calculation of the net area An of the plate is given by - An = Bt - nϕht + nss24ghere,B =…

Q: CLO3: Determine the tensile capacity of the 1/2-in. by 7-in. plate shown in Figure bellow. The…

A: Given: The cross-section of the plate is ½ in x 7 in. The diameter of the bolt is 6/8 in. The value…

Q: 4-2. Determine the following for the connection shown in Figure 4-26, assuming the bolts are -in.…

A: Bolted Connection: A small piece of metal that consists of a head and a shank is known as a Bolt.…

Q: Determine the LRFD design tensile strength of the bolted connection shown. The angles are connected…

A: Given dia of bolt=16 mm fy =250 fx =405 diameter of hole=16+2 =18 mm

Q: 2. Compute for the net area of the shape shown. (Note: Bolts are going through different portions of…

A: The section is provided above. It is w 10x19 section. Also 2 M20 bolts are provided in top and…

Q: Calculate the critical net area (mm²) for the tension member shown. The bolts are M22. 40 65 90 115…

A: Given A tension member Required Net area

Q: Example 5.13 The connection shown in Fig. Ex. 5.13 uses 20 mm diameter 10.9S grade bolts with…

A: Given that :

Q: GIVEN: PL ⅜ x 5 ½ of A242 steel ⅜ - inch thick gusset plate A242 steel ¾ - inch diameter bolts…

A: Compressive stress is the force that deforms the material in a way that reduces the volume of the…

Q: 3. A Channel section is connected to a 10mm gusset plate with 20mm- diameter bolts as shown in the…

Q: Determine the avaiable 2" streugth of 34" 3" 2 A325 -N bolts in 1.25 3" 3" 1.25" the lap splice with

A: The given data is: A 325-N bolts-with 3/4 diameter. The dimensions of the section is shown in…

Q: Problem 2: For the Channel as shown in the figure below determine the design and allowable strength.…

A: We have to determine the value of design and allowable strength. The holes are for 18 mm diameter…

Q: Two plates each with thickness t = 10 mm are bolted together with 6 - 16 mm diameter bolts forming a…

A: The thickness of the plates = 10 mm The connection provided = 6-16 mm bolts The yield strength of…

Q: The L7 x 4 x 1/2 single angle has two lines of bolts in the long leg as shown (See Figure). The U…

A: The distance from the centroid of the connected area to the plane of the connection, x=0.910 in The…

Q: Compute the governing net area of the plate shown below. The holes are for 3/4-in diameter bolts. Ir…

A: Compute the governing net area of the plate shown below. The holes are for 3/4-in diameter bolts.

Q: B. Determine the LRFD design strength and ASD allowable strength of the sections given. 1. A36 steel…

Q: If the connection is bolted connection, find the maximum load that can carried by the connection if…

A: Maximum Load carried by the connection Bearing strength of bolts and plate subjected to shear, Vdpb…

Q: Find the available strength of the S-shape shown in Figure 3.20. The holes are for 3/4-inch-diameter…

A: Given : The S shape is shown below : Dia of holes = 3/4 in. Using A36 steel FInd - The Available…

Q: Problem 1. The tension member is a PL 6 x 1/2. It is connected to a 3/8-inch-thick gusset plate with…

A: Answer Given in the Below attachments

Q: GOmm 5omm 10omM 100mm 100mm EOmm 150mm

A: Diamter of bolt (d) = 33 mm Let's 2mm extra is provide in hole So diameter of hole (dh) = 33+2 =…

Q: 1. In the butt joint shown below, the 7/8-inch diameter bolts are made of A325 steel with threads…

A: The width of the plate is B=12 in. The thickness of the plate is t=58 in. The diameter of the bolt…

Q: Determine the smallest net area of the tension member shown in the figure. The holes are for 3/4-in…

A: here given double angle sec so please keep this in mind for no. of bolt in net area calculations…

Q: What is the nominal, standard hole size for a 2" diameter bolt?

A: The correct answer is (a) 2.0625"

Q: Compute the net area of each of the given members.

A: Dimension of the plate=3/5 x 10 in2 Dia of the bolt ,d=1inch Line of bolts,n=1

Q: A double lap splice connection shown in figure B is made up of 6mm x 150mm and 9mm x 150mm. Use…

Question

Determine the net area of the given section below. Diameter of bolts is 7/8-in and the thickness of the plate is 3/8", in in. The channel used is C8x15 and the plate in
between the channels are 10" in width.
Select one:
а. 6.69
b. 3.43
c. 5.75
d. 2.25

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Introduction

VIEW

Step 2: Net area of the given section

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Which of the following gives the minimum number bolts that can be accommodated in one row of a 350mm flat plate. O 4 O 5 O 6 O 7
Help pls. Ill upvote :)
Determine the effective net area of a W 360 x 91 shown. The holes were punched for M20 bolts. 65 mm 0000 P O O DO 65 mm 60 85 85 85 mm mm mm mm
A C15x40 channel section is bolted to a gusset plate is used to resist a tensile loadPu =313 k. The bolts are 3/4 inch  diameter bolts A325 N (Group A, N Type) used insingle shear to resist this load. The bolts are to be symmetric and arranged in 3 rows.1) Determine the number of bolts needed for this connection. Draw a detailshowing how the bolts are arranged and showing spacing and edge distances onthis connection. Assume edge distance Le = 1.75db , use Le to nearest 1/4 in.2) If the connection is to be replaced by a fillet welded connection with transversewelds only along the channel web, determine the required fillet size to thenearest 16th of an inch.
1. An L 178 x 102 x 19 with one line of 20mm diameter bolts in each leg in usual gage as shown. Assume the connection length is 450mm. The pitch distance for the subsequent standard size holes is 75mm. Use ASTM A572M Grade 345 steel materials and : a. Determine the design strength of the member. b. Specify the maximum permitted length of the member as per AISC specifications.) 102mm g g 19mm 178mm L 178 x 102 x 19 Gusset Plate
1. Compute the critical net area of the 12-mm thick plate shown using AISC NSCP 2015 Specs (Section 504.3.2). The holes are punched for 19-mm bolts. Note that for a standard-size bolt hole, hole dia = bolt dia (in mm) + 3mm or hole dia. = bolt dia (in inches) + 1/8in. 25 mm 75 mm 275 75 m 25 m 75 mm 2. Determine the critical net area of the W12 x 16 shown in the figure, assuming that the holes are for 1-in bolts. 3 in W12 x 16 BỘ 3 in d = 12.00 in-0.220 in 3 in DO 3 in E by- 3.99 in+ 2 in 2 in 3. Determine the critical net area of an L8 x 6 x1/2 with staggered holes in each leg as shown in the figure. Holes are for 7/8-in diameter bolts. 2 2 4 @ 11 L8 x 6 x 2
Find the smallest net area for the plate shown below. The holes are for 1 in. diameter bolts.
Consider the following bolted connection. Slippage is permitted. Member: L6x6x3/4 3/16 “ gusset plate Pu Pu A36 steel 3.5* 1"diameter A325-X bolts 1 1/4" 3 " 3* 1 1/4" Question 3.1: Please, indicate if the combined bolt shear strength is closer to: Question 3.2: Please, indicate if the combined bolt bearing strength is closer to: Question 3.3: Please, indicate if the angle yielding strength is closer to: Question 3.4: Please, indicate if the angle fracture strength is closer to: Question 3.5: Please, indicate if the angle block shear strength is closer to: Question 3.6: Please, indicate if the overall connection strength is closer to:
What is the correct length of connection L? Please find an example of a tension member that has a staggered bolts.please find an attached picture. Thanks
Calculate the maximum tensile load, Ta or Tu of the connection shown in Figure 7. Theconnection consists of two 3/8" plates fastened to each side of one 13/16" plate.Assume 7/8" diameter bolts and standard punched holes. Use A36 steel. The plate is 13” wide. Note: Be sure to check all failure modes; bolt failure modes, and member failure modes(including block shear)
9. Determine the net area along route ABCDEF for the C380 x 50 (A, = 6430 mm) shown in the figure below. Holes are for 20 mm bolts. 36.4 mm 50mm 16.5 m 10.2 mm C380 x 50 B Igaje 36.4 mm - (a) 75 mm 230 mm 75 mm 50 mm BQ (b)
A tension member is 0.5 in. thick plate shown. The bolts are ¾ in. diameter high-strength bolts. The steel is A36. Compute the following: (Note: The dimensions are in "inches") The design strength for LFRD. The allowable strength for ASD.