Answered: Determine the net area along route…

Determine the net area along route ABCDEF for the C380 x 50 (A, = 6430 mm) shown in the figure below. Holes are for 20 mm bolts.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: SITUATION 1 The tension member shown in the figure contains holes for 1-in Ø bolts. At what spacing,…

Q: Select a W section bolted as shown in Figure 6.12 with %-in.-diameter bolts, and three bolts per…

Q: PL 3/8 x12" PL 3/8 x6" Pu or Pa + Pu or Pa Q3: Refer to the Q2 arrangement, if the two plates are to…

Q: O O Lin Figure -1 10in For the Section shown in the Figure-1 above, Compute connection capacity for…

A: A bolt is generally a metal pin with a head at one end and the ends are a shank threaded and receive…

Q: For the A36 beam shown in the accompanying illustration, what is the required spacing of 7/8-in A307…

A: Consider the free body diagram;

Q: What is the Nominal Shear Capacity of the following shear splice 3/4" A325N bolts W18x35 W24x55 F1…

A: Anb = 3.14 x (3/4)2 = 1.76625 sq inch fu = 105ksi FOS = 1.25

Q: The tension member shown contains holes for M20 bolts. At what spacing (mm), s, will the net area…

Q: draw -for the tread bars - 3-D 10 mm -for teh iser bars- d 10 mm @150 mm o.c. size of wooden…

A: We need to draw the reinforcement details of tread and riser

Q: 4. Determine the minimum net area of the angle section having a bolt hole with a clearance of 4mm.…

Q: Determine the net tensile area for the connection plate shown. Use a 3/8" plate with 3/4" bolts with…

A: Given data, Plate thickness (t)= (3/8) = inches Bolt dia = (3/4) inches So, hole diameter= dh =…

Q: ¿A Tension member has used to resist load of 65 kips, and the shear stress on bolts is 15.9 kips.…

A: If two or more plates are to be joined then the bolts or welding is used. The applied shear stress…

Q: Q17 An L4x4x7/16 tension member is connected with %"Ø bolts, as shown in the figure below. Both legs…

A: Given Data: The size of the tension member is L4×4×716. The diameter of the bolt is 34". To…

Q: 300 A W300 x 67 has two nes of 20 mm dia. Bolts in each lange (3 bolls in each line which has…

A: Steel sectionGross area, Web thickness, Flange width, Effective depth, Diameter of bolt, Yield…

Q: discuss the possible failure modes when in different bolts when the bolts are subjected to shear,…

A: Possible Failure Modes of Bolts in Shear, Tension, and Combined LoadingBolts are critical components…

Q: Problem 3. Lap connection is made of A325 % inch diameter bearing type bolts that threads are not in…

A: Answer A 325 group bolt 3/4 inch diameter bolt Plate 38 x 7 Plate 516 x 7 A 36 steel Live loadDead…

Q: Angle Bolted Connection. The L6 x 31/2 × 5/16. -in angles, shown in Figure, The bolts are 3/4 inch…

Q: For the connection shown in the accompanying illustration, Pu = 475 k and Pa = 320 k, determine the…

A: LRFD: Load and Resistance Factor Design is used for designing steel structures and structural…

Q: 2. Compute the design strength in tension, P, of the A36 steel plate (1/4 in x 12 in) with a line of…

A: Compute the design strength in tension, Pn, of the A36 steel plate (1/4 in 12in) with a line of…

Q: discuss the possible failure modes when in different bolts when the bolts are subjected to shear,…

A: ## Potential Failure Modes of Bolts in Shear, Tension, or Both**Understanding Bolt Failure**Bolts, a…

Q: the subject is steel strucure

A: Here's an outline for designing the floor slab with the given parameters and compiling the…

Q: a. Prepare a table showing values of Group A bolt shear strength and slip-critical strength for…

A: Shear strength: The maximum load that can be resisted by the structure is known as shear strength.…

Q: Problem 8: A C310 × 45 is connected with 25mm diameter bolts in each flange, as shown in Figure,…

A: LFRD stands for Load Resistance Factor Design, it is a method of designing concrete and steel…

Q: 2. Compute for the net area of the shape shown. (Note: Bolts are going through different portions of…

A: The section is provided above. It is w 10x19 section. Also 2 M20 bolts are provided in top and…

Q: Calculate the critical net area (mm²) for the tension member shown. The bolts are M22. 40 65 90 115…

A: Given A tension member Required Net area

Q: In your own words, explain what is meant by work.

A: Work is measurement of energy that is transferred when an body moves over a given length by an…

Q: Problem 3.. for 7/8 in bolts. . Compute the net area for the 7/8 x 12 plate shown below. The holes…

Q: Summarize the merits of HSFG bolts

A: The objective of the question is to understand the advantages or merits of High Strength Friction…

Q: Determine the net area of the given section below. Diameter of bolts is 7/8-in and the thickness of…

Q: The plate splice shown in the figure below has 9 – 3/4 inch diameter A325-N type bolts (Group A, N…

A: A325 N type of bolts, N indicates threaded portion will be in the shear plane. Dia of bolt = 3/4 in…

Q: Solution accu

A: Approach to solving the question:Understand the concept of net area: The net area is the effective…

Q: An A36 (Fy=248MPA, Fu=400MPA) steel plate with thickness, t=llmm used as a tension member is…

Q: 6. Given a sheared flat bar 8" in width, which is to have a double line of 1 3/8" Dia bolts, answer…

A: A sheared flat bar 8" in width, which is to have a double line of 1 3/8" Dia bolts.Need to finda.…

Q: Find the available strength of the S-shape shown in Figure 3.20. The holes are for 3/4-inch-diameter…

A: Given : The S shape is shown below : Dia of holes = 3/4 in. Using A36 steel FInd - The Available…

Q: 9.0 A C12 x 30 is connected with 25 mm diameter bolts in each flange, as shown. If Fy= 345 MPa, Fu=…

Q: Grade: 10.9 Included I Grade: S235 ace Class: C atio of the mean installed bolt pretension to the…

Q: 1. In the butt joint shown below, the 7/8-inch diameter bolts are made of A325 steel with threads…

A: The width of the plate is B=12 in. The thickness of the plate is t=58 in. The diameter of the bolt…

Q: A 3/4" x 10" X 5' long plate is fabricated from A36 steel and has standard holes for 3/4" bolts at…

Q: GROSS AREA, NET AREA AND EFFECTIVE NET AREA APPLICATIONS: Problem 2-9 A single lap joint is shown in…

A: 1.Gross Area Ag=wg×twhere,wg=width of plate 1t=thickness of plate 1…

Q: Problem 3.. for 7/8 in bolts. . Compute the net area for the 7/8 x 12 plate shown below. The holes…

Q: Can somebody show me how to identify the following members (highlight them if needed, I truly need…

A: Note:- I think the given truss is wrong as the truss consists of only 5 joints and the numbering is…

Q: A double cover butt joint is shown in figure 2 below. If the steel is Grade S355JR and the bolts are…

A: Given, For Steel grade S355JR, fy=350 MPafu=490 MPa For bolts of 8.8 grade, fub =800 N/mm2 Assuming…

Question

9. Determine the net area along route ABCDEF for the C380 x 50 (A, = 6430 mm)
shown in the figure below. Holes are for 20 mm bolts.
36.4 mm
50mm
16.5 m
10.2 mm
C380 x 50
B
Igaje
36.4 mm
-
(a)
75 mm
230 mm
75 mm
50 mm
BQ
(b)

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Compute the effective net area of the built-up section shown below if the holes are punched for 22mm bolts. Assume U=0.90. The relevant data are Ac=4,735.00 mm2 for each channel, tw=9.8 mm, tf = 12.7 mm.
A double lap splice connection shown in figure B is made up of 6mm x 150mm and 9mm x 150mm. Use NSCP specifications and assume a double row of bolts with standardsize holes for a bearing type connection with threads excluded from the shear planes.Minimum tensile strength Fu = 552.93MPa. Assume diameter hole is 3mm bigger than thediameter of bolts. Allowable shear stress is Fv = 207MPa. Allowable bearing stress fb = 1.2Fu.Diameter of bolts is 19mm. Fy = 449.25MPa.(a) Compute the tensile capacity of the steel plates. (Max. Net Area = 0.85 of Gross Area)(b) Compute the number of 19mm diameter bolts to develop the full strength of the plates. Note: SHOW DRAWINGS AND SOLUTIONS.
Find the design strength (LRFD) and allowable strength (ASD) of S15 X 50 as shown in figure below. The holes are for 1 in diameter bolts. Use A36 steel for computation.
Determine the effective net area of a W 360 x 91 shown. The holes were punched for M20 bolts. 65 mm 0000 P O O DO 65 mm 60 85 85 85 mm mm mm mm
A C15x40 channel section is bolted to a gusset plate is used to resist a tensile loadPu =313 k. The bolts are 3/4 inch  diameter bolts A325 N (Group A, N Type) used insingle shear to resist this load. The bolts are to be symmetric and arranged in 3 rows.1) Determine the number of bolts needed for this connection. Draw a detailshowing how the bolts are arranged and showing spacing and edge distances onthis connection. Assume edge distance Le = 1.75db , use Le to nearest 1/4 in.2) If the connection is to be replaced by a fillet welded connection with transversewelds only along the channel web, determine the required fillet size to thenearest 16th of an inch.
1. An L 178 x 102 x 19 with one line of 20mm diameter bolts in each leg in usual gage as shown. Assume the connection length is 450mm. The pitch distance for the subsequent standard size holes is 75mm. Use ASTM A572M Grade 345 steel materials and : a. Determine the design strength of the member. b. Specify the maximum permitted length of the member as per AISC specifications.) 102mm g g 19mm 178mm L 178 x 102 x 19 Gusset Plate
In mm) Problem 8: A C310 × 45 is connected with 25mm diameter bolts in each flange, as shown in Figure, Problem 11. If Fy = 345MPA, Fu = 450MPA, and Ae = 0.90An, Apply the following %3D %3D %3D approaches to determine: a. The design strength for LRFD. b. The allowable strength for ASD. Section Figure. Problem 8
Please help
4. Given a sheared flat bar 5" in width, which is to have a double line of 3/4" Dia bolts, answer the following. a. Does the bolt hole pattern need to be staggered? b. What is the minimum edge distance required? c. What is the gage distance? d. What is the clearance "E" required? e. What is the diagonal minimum distance? f. What is the minimum pitch?
Determine the design strength of an UNP200 with four lines if 16 mm diameter bolts in standard holes, as shown in the Figure below. F = 370MPA F. = 240MPa 60 80 60 100, 100, 100, 100,100 UNP 200
For high strength bolts with M20, 10.9 grade, please explain the meaning of '20', '10' and '.9'.
Determine the capacity of the details shown below.A992: Fy=50ksi, Fu=65ksiA36: Fy=36ksi, Fu=58ksieffective bolt hole diameter = bolt hole + 1/16"beam properties: tw=0.38 in., bf=7.07 in., tf=0.63 in.Fexx=70ksi l) what is the bolt bearing capacity of beam flange of the flange connection in kips? (2 decimal places)