B. Determine the LRFD design strength and ASD allowable strength of the sections given. 1. A36 steel and 7/8"-diameter bolts

Q: Compute L, T, E, M, LC, R, and stations of the PC and PT for the highway curve with D,-400,…

A:

Q: D. SKETCH: (Draw the resulting figure based on the data given on a graphing paper. Vertical axis or…

A: Station BS HI FS IFS Elevation (m) BM -1 1.515 101.515     100 0+000       1.520 99.995…

Q: The following is the bearing and length measurements of an opentraverse A) Determine the latitude…

A: The latitude of the traverse line is extend on the north and south direction and departure of the…

Q: TECHNICAL DESCRIPTIONS Bearing S 22°06' E S72 20' W N 15°34' E N 30°09' E S 10°22' E S 17'47' W S…

A:

Q: In the exhibit below, What is the distance from A to C, A O 1078.57' O 1087.75' O 1187.57' O…

A: Given values: Consider closed traverse given. For closed traverse, sum of latitude and sum of…

Q: Example: reading around a 10x10 cm square area = 0.995 rev Reading around the required area = 5.765…

A: 10 cm square =0.995 rev 1 cm square=0.00995 rev area of required area=5.765 rev required area in cm…

Q: What are GNSS receivers?

A: Full form is Global Navigation Satellite System.

Q: Block properties: Length (L) = 134 mm Width (W) = 99 mm Height (H) = 60 mm E = 58 MPa V = 0.40…

A: Answer We are given Length L = 134 mm Width W = 99 mm Height H = 60 mm E = 58 Mpa ν = 0.40 σ1 = 26.4…

Q: : Find the area of the polygon ABCE (AVE area). Latitude Departure E Line W AB BC 65 80 CD 80 20 DE…

A: SINCE  latitude and departure of line AB is not given we need to find them   In a closed traverse :…

Q: What is the interior angle of CP#1? Answer in the format ddd-mm-ss without any Instrument is @ CP#1…

A: If BS is CP#6 and, FS is CP#2 And angle is taken from right then this angle must be exterior angle…

Q: Area of the Triangles are denoted by the following formulas: 1. Basic Formula, A = 12 * base*…

A: Given: From the figure, AC=1690.54 m

Q: Define compensated mats

A: The compensated raft is also called a floating raft or floating foundation.  It is the foundation,…

Q: Determine the x- and y-coordinates of the centroid of the shaded ar ! 3", 3" 4" 1.25" 10" 1.25" 3" B…

A:

Q: What is the length of the dividing line? (Type your answer using 2 decimal places, numerical value…

A:

Q: What is PD 1096. Explain

A:

Q: 239,0 185.2 O'ନ୍ଧ୍ୟା NETI (D) (89 ୬ଗ F 6 3d),6 8''tt ଠଆ neer

A:

Q: Problem 3 Below is a profile level notes, indicate the missing data, show arithmetic check, and draw…

A: station B.S H.I F.S I.F.S Elevation BM1 1.08 36.56     35.48 1+000       2.01 34.55 1+020…

Q: What are the problems faced by the ncorrect lengths of tape?

A: Tapes are widely used in surveying for measurement purpose. It is used to determine horizontal,…

Q: hat are the uses of hydrographs?

A: A hydrograph may be used to show how the  water flow in a drainage basin particularly river runoff…

Q: Draw front and top view in Ist angle projection 016 R20 14 44 24 1. 40 30

A: >>>Given that the figure is ISOMETRIC diagram and we have to draw it in a 1st angle…

Q: earson MyLab and Mastering X roblem 9.19…

A:

Q: Define Aerial Photographs.

A: Aerial Photographs:

Q: "I in terms of BVC station EVC | L = ( 10+19.25) (륵 드 (PVI Station - = (77400) - (10+ 19.25) = (77…

A: BVC (Beginning of Vertical Curve) PVI (Point of Vertical Intersection) EVC (End of Vertical Curve)

Q: 7. Water flows under constant head through the two soil samples 1 and 2, as shown in the figure. The…

A:

Q: -20 +0.50 20/3

A:

Q: g1= Station 18+26 18+00 17+00 16+00 15+68 g2= X 0 Elevation of BVC = gix 82-81x2 2L Elevation 899.02

A: Vertical Curve : Vertical curves, which may or may not be symmetrical, are supplied to alter the…

Q: Determine coordinates of centroid of the following shaded area.

A: Centroid is the point where the whole weight of the body acts. If the section is made up of…

Q: 5/49 Determine the x- and y-coordinates of the centroid of the shaded area. -50 y I -150- 100…

A: The below figure is given,

Q: 20 20 FRONT ELEVATION 60 20 60

A: For given isometric view following are top, front and side views are first angle projection views

Q: In the exhibit below, What is the distance from A to C, A O 1078.57¹ O 1087.75' O 1187.57' O…

A: To Determine Distance from A to C, L = ?

Q: 1 / 2 \text { inch } \times 1 / 4

A: To find:- 1/2*1/4

Q: What are point positioning equations?

A: Point positioning are used for positioning with GPS. In point positioning, a GPS receiver which…

Q: How are satellites identified?

A: INTRODUCTION:- A satellite is an item this is intentionally positioned into orbit. These gadgets are…

Q: Describe the content of the GPS broadcast message

A: GPS (Global positioning system) : The Global Positioning System (GPS), formerly known as Navstar…

Q: What are roving receivers?

A: GPS is a navigation as well as a positioning system that relies on a network of 24 satellites. The…

Q: Determine coordinates of centroid of the following shaded area.

A: Hi! Thank you for the question, As per the honor code, We’ll answer the first question since the…

Q: How much is the strike separation (i.e., line AB on the map)? Scale: 18mm = 100m 82m 181m 67m 24m O…

A: AB = 32 mm

Electrical Plans

An electrical plan is also known as an electrical drawing or a wiring diagram. It is a kind of visual representation which bears the blueprint symbols of all the electrical components in electrical house plans or various building construction projects. In other words, electrical plans describe electrical circuits and systems that build up the electrical house plans or building plans. An electrical engineer who works on various construction projects creates an electrical drawing. The engineer outlines the electric planning with different symbols and lines forming a detailed electrical circuit. These drawings are a means of representation for the clients, who will carry out the actual wiring process. In a nutshell, an electrical plan showcases the circuitry with the proper placement of electric components.